lkml.org 
[lkml]   [2018]   [Mar]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 02/19] csky: Exception handling and syscall
Hi Mark,

> Here you open code an MFCR instruction.
>
> I guess MFCR stands for something like move-from-control-register, and MTCR
> stands for move-to-control-register?
>
> I see that later on you have helpers for specific registers, e.g. mfcr_cpuidrr().
>
> You might want to follow the example of arm64's read_sysreg() and
> write_sysreg(), and have general purpose helpers for thos instructions, e.g.
>
> #define mfcr(reg) \
> ({ \
> unsigned long __mfcr_val; \
> asm volatile("mfcr %0, " #reg "\n" : "=r" (__mfr_val)); \
> __mfcr_val; \
> })
>
> ... which avoids needing helpers for each register, as you can do:
>
> ss1_val = mfcr(ss1);
> cpuidrr_val = mfcr(cpuidrr);
>
OK, good idea.

> > + if (memblock_start_of_DRAM() != (PHYS_OFFSET + CONFIG_RAM_BASE)) {
> > + pr_err("C-SKY: dts-DRAM doesn't fit .config: %x-%x.\n",
> > + memblock_start_of_DRAM(),
> > + PHYS_OFFSET + CONFIG_RAM_BASE);
> > + return;
> > + }
>
> If this is a problem, is it safe to continue at all?
>
> Why does the base address of RAM matter?
>
We use mips-like direct-mapping tech, and it need 512MB boundary
alignment. And few users need non-512MB boundary phy-addr start,
so we give the CONFIG_RAM_BASE for determine the offset to PHYS_OFFSET.

> > +
> > + mtcr_msa0(PHYS_OFFSET | 0xe);
> > + mtcr_msa1(PHYS_OFFSET | 0x6);
>
> As with MFCR, you could use a generic helper here, e.g.
>
> #define mtcr(val, reg) \
> do { \
> asm volatile("mtcr %0, " #reg "\n" : "=r" ((unsigned long)val)); \
> } while (0);
>
> mtcr(PHYS_OFFSET | 0xe, msa0)
> mtcr(PHYS_OFFSET | 0x6, msa1)
>
OK

> > + seq_printf(m, "C-SKY CPU : %s\n", CSKYCPU_DEF_NAME);
> > + seq_printf(m, "revision : 0x%08x\n", mfcr_cpuidrr());
> > + seq_printf(m, "ccr reg : 0x%08x\n", mfcr_ccr());
> > + seq_printf(m, "ccr2 reg : 0x%08x\n", mfcr_ccr2());
> > + seq_printf(m, "hint reg : 0x%08x\n", mfcr_hint());
> > + seq_printf(m, "msa0 reg : 0x%08x\n", mfcr_msa0());
> > + seq_printf(m, "msa1 reg : 0x%08x\n", mfcr_msa1());
>
> Do these need to be exposed to userspace?
>
Yes, I'll add more explain info.

> Does this arch support SMP? I see you don't log information per-cpu.
This patch-set doesn't support SMP.
>
> > diff --git a/arch/csky/kernel/entry.S b/arch/csky/kernel/entry.S
>
> > +#define THREADSIZE_MASK_BIT 13
>
> You might want to define this as THREAD_SHIFT, and define THREAD_SIZE in terms
> of it, so that they're guaranteed to be in sync
>
> e.g. in your <asm/thread_info.h> have:
>
> #define THREAD_SHIFT 13
> #define THREAD_SIZE (1 << THREAD_SHIFT)
OK

> If you have a spare register that you can point at the current task (or you
> have preemption-safe percpu ops), I'd recommend moving the thread_info off of
> the stack, and implementing THREAD_INFO_IN_TASK_STRUCT.
>
Em... I'll think about it.

> For consistency, and in case you change your stack size in future, this should
> be THREADSIZE_MASK_BIT.
>
OK

> > + if (unlikely(address >= VMALLOC_START && address <= VMALLOC_END))
> > + goto vmalloc_fault;
>
> You might want to check if this was a user mode fault here, so that users can't trigger vmalloc faults.
Is it necessary to check user mode? If a user-process touch a
kernel-addr, it will cause a supervisor exception.

Best Regards
Guo Ren

\
 
 \ /
  Last update: 2018-03-19 07:49    [W:0.835 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site