lkml.org 
[lkml]   [2018]   [Mar]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v5 1/2] hwmon: (ucd9000) Add gpio chip interface
On Fri, Mar 16, 2018 at 01:39:48PM -0500, Eddie James wrote:
>
>
> On 03/16/2018 08:40 AM, Guenter Roeck wrote:
> >On 03/15/2018 03:21 PM, Eddie James wrote:
> >>From: Christopher Bostic <cbostic@linux.vnet.ibm.com>
> >>
> >>Add a struct gpio_chip and define some methods so that this device's
> >>I/O can be accessed via /sys/class/gpio.
> >>
> >
> >Sorry for not noticing earlier. The 0day reports should be addressed by
> >selecting GPIOLIB
> >in the Kconfig entry.
>
> Getting kbuild recursive dependencies when I select GPIOLIB for ucd9000 :(
>
Sure, it would have been too easy otherwise.

> May have to do "depends on" instead and #ifdef GPIOLIB in ucd9000, unless
> you have another recommendation?
>

Good news is that the code is all in one code block in the driver,
so make it #ifdef and

...
#else
static void ucd9000_probe_gpio(...) { }
#endif

With that, you won't need "depends on ..."

Thanks,
Guenter

> Thanks
> Eddie
>
> >
> >Guenter
> >
> >>Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
> >>Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
> >>Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
> >>---
> >>  drivers/hwmon/pmbus/ucd9000.c | 201
> >>++++++++++++++++++++++++++++++++++++++++++
> >>  1 file changed, 201 insertions(+)
> >>
> >>diff --git a/drivers/hwmon/pmbus/ucd9000.c
> >>b/drivers/hwmon/pmbus/ucd9000.c
> >>index b74dbec..a34ffc4 100644
> >>--- a/drivers/hwmon/pmbus/ucd9000.c
> >>+++ b/drivers/hwmon/pmbus/ucd9000.c
> >>@@ -27,6 +27,7 @@
> >>  #include <linux/slab.h>
> >>  #include <linux/i2c.h>
> >>  #include <linux/pmbus.h>
> >>+#include <linux/gpio.h>
> >>  #include "pmbus.h"
> >>    enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd9090,
> >>ucd90910 };
> >>@@ -35,8 +36,18 @@
> >>  #define UCD9000_NUM_PAGES        0xd6
> >>  #define UCD9000_FAN_CONFIG_INDEX    0xe7
> >>  #define UCD9000_FAN_CONFIG        0xe8
> >>+#define UCD9000_GPIO_SELECT        0xfa
> >>+#define UCD9000_GPIO_CONFIG        0xfb
> >>  #define UCD9000_DEVICE_ID        0xfd
> >>  +/* GPIO CONFIG bits */
> >>+#define UCD9000_GPIO_CONFIG_ENABLE    BIT(0)
> >>+#define UCD9000_GPIO_CONFIG_OUT_ENABLE    BIT(1)
> >>+#define UCD9000_GPIO_CONFIG_OUT_VALUE    BIT(2)
> >>+#define UCD9000_GPIO_CONFIG_STATUS    BIT(3)
> >>+#define UCD9000_GPIO_INPUT        0
> >>+#define UCD9000_GPIO_OUTPUT        1
> >>+
> >>  #define UCD9000_MON_TYPE(x)    (((x) >> 5) & 0x07)
> >>  #define UCD9000_MON_PAGE(x)    ((x) & 0x0f)
> >>  @@ -47,9 +58,15 @@
> >>    #define UCD9000_NUM_FAN        4
> >>  +#define UCD9000_GPIO_NAME_LEN    16
> >>+#define UCD9090_NUM_GPIOS    23
> >>+#define UCD901XX_NUM_GPIOS    26
> >>+#define UCD90910_NUM_GPIOS    26
> >>+
> >>  struct ucd9000_data {
> >>      u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
> >>      struct pmbus_driver_info info;
> >>+    struct gpio_chip gpio;
> >>  };
> >>  #define to_ucd9000_data(_info) container_of(_info, struct
> >>ucd9000_data, info)
> >>  @@ -149,6 +166,188 @@ static int ucd9000_read_byte_data(struct
> >>i2c_client *client, int page, int reg)
> >>  };
> >>  MODULE_DEVICE_TABLE(of, ucd9000_of_match);
> >>  +static int ucd9000_gpio_read_config(struct i2c_client *client,
> >>+                    unsigned int offset)
> >>+{
> >>+    int ret;
> >>+
> >>+    /* No page set required */
> >>+    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT,
> >>offset);
> >>+    if (ret < 0)
> >>+        return ret;
> >>+
> >>+    return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG);
> >>+}
> >>+
> >>+static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset)
> >>+{
> >>+    struct i2c_client *client  = gpiochip_get_data(gc);
> >>+    int ret;
> >>+
> >>+    ret = ucd9000_gpio_read_config(client, offset);
> >>+    if (ret < 0)
> >>+        return ret;
> >>+
> >>+    return !!(ret & UCD9000_GPIO_CONFIG_STATUS);
> >>+}
> >>+
> >>+static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset,
> >>+                 int value)
> >>+{
> >>+    struct i2c_client *client = gpiochip_get_data(gc);
> >>+    int ret;
> >>+
> >>+    ret = ucd9000_gpio_read_config(client, offset);
> >>+    if (ret < 0) {
> >>+        dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n",
> >>+            offset, ret);
> >>+        return;
> >>+    }
> >>+
> >>+    if (value) {
> >>+        if (ret & UCD9000_GPIO_CONFIG_STATUS)
> >>+            return;
> >>+
> >>+        ret |= UCD9000_GPIO_CONFIG_STATUS;
> >>+    } else {
> >>+        if (!(ret & UCD9000_GPIO_CONFIG_STATUS))
> >>+            return;
> >>+
> >>+        ret &= ~UCD9000_GPIO_CONFIG_STATUS;
> >>+    }
> >>+
> >>+    ret |= UCD9000_GPIO_CONFIG_ENABLE;
> >>+
> >>+    /* Page set not required */
> >>+    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
> >>+    if (ret < 0) {
> >>+        dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
> >>+            offset, ret);
> >>+        return;
> >>+    }
> >>+
> >>+    ret &= ~UCD9000_GPIO_CONFIG_ENABLE;
> >>+
> >>+    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
> >>+    if (ret < 0)
> >>+        dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
> >>+            offset, ret);
> >>+}
> >>+
> >>+static int ucd9000_gpio_get_direction(struct gpio_chip *gc,
> >>+                      unsigned int offset)
> >>+{
> >>+    struct i2c_client *client = gpiochip_get_data(gc);
> >>+    int ret;
> >>+
> >>+    ret = ucd9000_gpio_read_config(client, offset);
> >>+    if (ret < 0)
> >>+        return ret;
> >>+
> >>+    return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE);
> >>+}
> >>+
> >>+static int ucd9000_gpio_set_direction(struct gpio_chip *gc,
> >>+                      unsigned int offset, bool direction_out,
> >>+                      int requested_out)
> >>+{
> >>+    struct i2c_client *client = gpiochip_get_data(gc);
> >>+    int ret, config, out_val;
> >>+
> >>+    ret = ucd9000_gpio_read_config(client, offset);
> >>+    if (ret < 0)
> >>+        return ret;
> >>+
> >>+    if (direction_out) {
> >>+        out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0;
> >>+
> >>+        if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) {
> >>+            if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val)
> >>+                return 0;
> >>+        } else {
> >>+            ret |= UCD9000_GPIO_CONFIG_OUT_ENABLE;
> >>+        }
> >>+
> >>+        if (out_val)
> >>+            ret |= UCD9000_GPIO_CONFIG_OUT_VALUE;
> >>+        else
> >>+            ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE;
> >>+
> >>+    } else {
> >>+        if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE))
> >>+            return 0;
> >>+
> >>+        ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE;
> >>+    }
> >>+
> >>+    ret |= UCD9000_GPIO_CONFIG_ENABLE;
> >>+    config = ret;
> >>+
> >>+    /* Page set not required */
> >>+    ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG,
> >>config);
> >>+    if (ret < 0)
> >>+        return ret;
> >>+
> >>+    config &= ~UCD9000_GPIO_CONFIG_ENABLE;
> >>+
> >>+    return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG,
> >>config);
> >>+}
> >>+
> >>+static int ucd9000_gpio_direction_input(struct gpio_chip *gc,
> >>+                    unsigned int offset)
> >>+{
> >>+    return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_INPUT,
> >>0);
> >>+}
> >>+
> >>+static int ucd9000_gpio_direction_output(struct gpio_chip *gc,
> >>+                     unsigned int offset, int val)
> >>+{
> >>+    return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT,
> >>+                      val);
> >>+}
> >>+
> >>+static void ucd9000_probe_gpio(struct i2c_client *client,
> >>+                   const struct i2c_device_id *mid,
> >>+                   struct ucd9000_data *data)
> >>+{
> >>+    int rc;
> >>+
> >>+    switch (mid->driver_data) {
> >>+    case ucd9090:
> >>+        data->gpio.ngpio = UCD9090_NUM_GPIOS;
> >>+        break;
> >>+    case ucd90120:
> >>+    case ucd90124:
> >>+    case ucd90160:
> >>+        data->gpio.ngpio = UCD901XX_NUM_GPIOS;
> >>+        break;
> >>+    case ucd90910:
> >>+        data->gpio.ngpio = UCD90910_NUM_GPIOS;
> >>+        break;
> >>+    default:
> >>+        return; /* GPIO support is optional. */
> >>+    }
> >>+
> >>+    /*
> >>+     * Pinmux support has not been added to the new gpio_chip.
> >>+     * This support should be added when possible given the mux
> >>+     * behavior of these IO devices.
> >>+     */
> >>+    data->gpio.label = client->name;
> >>+    data->gpio.get_direction = ucd9000_gpio_get_direction;
> >>+    data->gpio.direction_input = ucd9000_gpio_direction_input;
> >>+    data->gpio.direction_output = ucd9000_gpio_direction_output;
> >>+    data->gpio.get = ucd9000_gpio_get;
> >>+    data->gpio.set = ucd9000_gpio_set;
> >>+    data->gpio.can_sleep = true;
> >>+    data->gpio.base = -1;
> >>+    data->gpio.parent = &client->dev;
> >>+
> >>+    rc = devm_gpiochip_add_data(&client->dev, &data->gpio, client);
> >>+    if (rc)
> >>+        dev_warn(&client->dev, "Could not add gpiochip: %d\n", rc);
> >>+}
> >>+
> >>  static int ucd9000_probe(struct i2c_client *client,
> >>               const struct i2c_device_id *id)
> >>  {
> >>@@ -263,6 +462,8 @@ static int ucd9000_probe(struct i2c_client *client,
> >>            | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
> >>      }
> >>  +    ucd9000_probe_gpio(client, mid, data);
> >>+
> >>      return pmbus_do_probe(client, mid, info);
> >>  }
> >>
> >
>

\
 
 \ /
  Last update: 2018-03-16 19:54    [W:0.048 / U:2.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site