lkml.org 
[lkml]   [2018]   [Feb]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] cpufreq: imx6q: support frequencies >528MHz for i.MX6UL/ULL
On 09.02.2018 12:52, Rafael J. Wysocki wrote:
> On Friday, January 19, 2018 12:58:36 AM CET Stefan Agner wrote:
>> Depending on SKU i.MX6UL/i.MX6ULL support frequencies up to 900MHz.
>> Use PLL1 sys clock for all operating points higher than 528MHz.
>>
>> Note: For higher operating points VDD_SOC_IN needs to be 125mV
>> higher than the ARM set-point (see datasheet). Specifically, the
>> i.MX6UL/ULL EVK boards have an external DC regulator which needs
>> adjustment. The regulator adjustment is not covered with this
>> change.
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>
> This makes sense to me, but I need someone with the requisite platform
> knowledge to review it.
>

Fabio, Leonard, maybe one of you could have a look at it?

It is similar to what ("cpufreq: imx: Add support for 700MHz setpoint in
cpufreq") in downstream is doing, it avoids changing pll twice though.

And, as mentioned in the commit log, the dc_reg part is missing. This is
because it is not required on our Colibri iMX6ULL since it uses a higher
(not switchable) VDD_SOC_IN voltage by default.

--
Stefan

>> ---
>> drivers/cpufreq/imx6q-cpufreq.c | 14 ++++++++------
>> 1 file changed, 8 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c
>> index 628fe899cb48..840f6386c780 100644
>> --- a/drivers/cpufreq/imx6q-cpufreq.c
>> +++ b/drivers/cpufreq/imx6q-cpufreq.c
>> @@ -114,12 +114,14 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
>> */
>> clk_set_rate(arm_clk, (old_freq >> 1) * 1000);
>> clk_set_parent(pll1_sw_clk, pll1_sys_clk);
>> - if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk))
>> - clk_set_parent(secondary_sel_clk, pll2_bus_clk);
>> - else
>> - clk_set_parent(secondary_sel_clk, pll2_pfd2_396m_clk);
>> - clk_set_parent(step_clk, secondary_sel_clk);
>> - clk_set_parent(pll1_sw_clk, step_clk);
>> + if (freq_hz <= clk_get_rate(pll2_bus_clk)) {
>> + if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk))
>> + clk_set_parent(secondary_sel_clk, pll2_bus_clk);
>> + else
>> + clk_set_parent(secondary_sel_clk, pll2_pfd2_396m_clk);
>> + clk_set_parent(step_clk, secondary_sel_clk);
>> + clk_set_parent(pll1_sw_clk, step_clk);
>> + }
>> } else {
>> clk_set_parent(step_clk, pll2_pfd2_396m_clk);
>> clk_set_parent(pll1_sw_clk, step_clk);
>>

\
 
 \ /
  Last update: 2018-02-09 13:06    [W:0.105 / U:0.072 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site