lkml.org 
[lkml]   [2018]   [Feb]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/2] input: touchscreen: ar1021_i2c: enable touch mode during open
Hi all.

2017-04-27 14:22 GMT+02:00 Martin Kepplinger <martin.kepplinger@ginzinger.com>:
> The device could as well be in command mode, in which this driver cannot
> handle the device. When opening the device, let's make sure the device
> will be in the mode we expect it to be for this driver.
>

I run into issues caused by this change. It turns out that the device
is non-functional
after some warm-reboots and as a result I am not able to use xorg's
evdev driver.
So I have some questions about this change:

* Should we enable irq before calling i2c_master_send(..) as the chip raises an
irq if the command was processed?

* Would it be enough to send this command only once during driver
lifetime? I can
see that on my system open gets called 3 times during boot-up.

* What are the circumstances the touch device would be in an other state? In the
official kernel driver the userspace can send commands via sysfs.
Also the driver
does set the touch enable mode as this patch does.


> Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
> ---
> drivers/input/touchscreen/ar1021_i2c.c | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
> diff --git a/drivers/input/touchscreen/ar1021_i2c.c b/drivers/input/touchscreen/ar1021_i2c.c
> index 1a94d8b..2a76231 100644
> --- a/drivers/input/touchscreen/ar1021_i2c.c
> +++ b/drivers/input/touchscreen/ar1021_i2c.c
> @@ -18,6 +18,12 @@
> #define AR1021_MAX_X 4095
> #define AR1021_MAX_Y 4095
>
> +#define AR1021_CMD 0x55
> +#define AR1021_TOUCH 0x80
> +
> +#define AR1021_CMD_ENABLE_TOUCH 0x12
> +#define AR1021_CMD_DISABLE_TOUCH 0x13
> +
> struct ar1021_i2c {
> struct i2c_client *client;
> struct input_dev *input;
> @@ -58,6 +64,15 @@ static int ar1021_i2c_open(struct input_dev *dev)
> {
> struct ar1021_i2c *ar1021 = input_get_drvdata(dev);
> struct i2c_client *client = ar1021->client;
> + int error;
> + u8 cmd_enable_touch[3] = {AR1021_CMD,
> + 0x01, /* number of bytes after this */
> + AR1021_CMD_ENABLE_TOUCH };
> +
> + error = i2c_master_send(ar1021->client, cmd_enable_touch,
> + sizeof(cmd_enable_touch));
> + if (error < 0)
> + return error;
>
> enable_irq(client->irq);
>
> --
> 2.1.4
>

--
greets
--
Christian Gmeiner, MSc

https://christian-gmeiner.info

\
 
 \ /
  Last update: 2018-02-05 11:09    [W:0.103 / U:1.156 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site