lkml.org 
[lkml]   [2018]   [Feb]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v7 6/6] drm/msm: iommu: Replace runtime calls with runtime suppliers
On Tue, Feb 13, 2018 at 4:10 AM, Tomasz Figa <tfiga@chromium.org> wrote:
> Hi Vivek,
>
> Thanks for the patch. Please see my comments inline.
>
> On Wed, Feb 7, 2018 at 7:31 PM, Vivek Gautam
> <vivek.gautam@codeaurora.org> wrote:
>> While handling the concerned iommu, there should not be a
>> need to power control the drm devices from iommu interface.
>> If these drm devices need to be powered around this time,
>> the respective drivers should take care of this.
>>
>> Replace the pm_runtime_get/put_sync(<drm_device>) with
>> pm_runtime_get/put_suppliers(<drm_device>) calls, to power-up
>> the connected iommu through the device link interface.
>> In case the device link is not setup these get/put_suppliers()
>> calls will be a no-op, and the iommu driver should take care of
>> powering on its devices accordingly.
>>
>> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>> ---
>> drivers/gpu/drm/msm/msm_iommu.c | 16 ++++++++--------
>> 1 file changed, 8 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/msm/msm_iommu.c b/drivers/gpu/drm/msm/msm_iommu.c
>> index b23d33622f37..1ab629bbee69 100644
>> --- a/drivers/gpu/drm/msm/msm_iommu.c
>> +++ b/drivers/gpu/drm/msm/msm_iommu.c
>> @@ -40,9 +40,9 @@ static int msm_iommu_attach(struct msm_mmu *mmu, const char * const *names,
>> struct msm_iommu *iommu = to_msm_iommu(mmu);
>> int ret;
>>
>> - pm_runtime_get_sync(mmu->dev);
>> + pm_runtime_get_suppliers(mmu->dev);
>> ret = iommu_attach_device(iommu->domain, mmu->dev);
>> - pm_runtime_put_sync(mmu->dev);
>> + pm_runtime_put_suppliers(mmu->dev);
>
> For me, it looks like a wrong place to handle runtime PM of IOMMU
> here. iommu_attach_device() calls into IOMMU driver's attach_device()
> callback and that's where necessary runtime PM gets should happen, if
> any. In other words, driver A (MSM DRM driver) shouldn't be dealing
> with power state of device controlled by driver B (ARM SMMU).

Note that we end up having to do the same, because of iommu_unmap()
while DRM driver is powered off.. it might be cleaner if it was all
self contained in the iommu driver, but that would make it so other
drivers couldn't call iommu_unmap() from an irq handler, which is
apparently something that some of them want to do..

So I'm happy with the pm_runtime_get/put_suppliers() approach as a
reasonable compromise.

(Perhaps specifically, attach/detach this could move inside the iommu
driver, but we still need to get/put_suppliers() for unmap(), so meh)

BR,
-R

> This is also important for the reasons I stated in my comments to
> "[PATCH v7 1/6] base: power: runtime: Export
> pm_runtime_get/put_suppliers". Quoting for everyone's convenience:
>
>>> There are however cases in which the consumer wants to power-on
>>> the supplier, but not itself.
>>> E.g., A Graphics or multimedia driver wants to power-on the SMMU
>>> to unmap a buffer and finish the TLB operations without powering
>>> on itself.
>>
>>This sounds strange to me. If the SMMU is powered down, wouldn't the
>>TLB lose its contents as well (and so no flushing needed)?
>>
>>Other than that, what kind of hardware operations would be needed
>>besides just updating the page tables from the CPU?
>>
>
> In other words, the SMMU driver can deal with hardware state based on
> return value of pm_runtime_get_sync() or pm_runtime_get_if_in_use()
> and decide whether some operations are necessary or not, e.g.
> - a state restore is necessary if the domain was powered off, but we
> are bringing the master on,
> - a flush may not be required when (un)mapping with the domain powered off,
> - etc.
>
> Best regards,
> Tomasz

\
 
 \ /
  Last update: 2018-02-13 19:03    [W:0.175 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site