lkml.org 
[lkml]   [2018]   [Feb]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 2/4] drivers: firmware: xilinx: Add ZynqMP firmware driver
On Thu, Feb 01, 2018 at 01:23:48AM +0000, Jolly Shah wrote:
> Hi Mark,
> Thanks for the review,
>
> > -----Original Message-----
> > From: Mark Rutland [mailto:mark.rutland@arm.com]
> > Sent: Wednesday, January 31, 2018 10:20 AM
> > To: Jolly Shah <JOLLYS@xilinx.com>
> > Cc: ard.biesheuvel@linaro.org; mingo@kernel.org;
> > gregkh@linuxfoundation.org; matt@codeblueprint.co.uk;
> > sudeep.holla@arm.com; hkallweit1@gmail.com; keescook@chromium.org;
> > dmitry.torokhov@gmail.com; michal.simek@xilinx.com; robh+dt@kernel.org;
> > linux-arm-kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> > devicetree@vger.kernel.org; Jolly Shah <JOLLYS@xilinx.com>; Rajan Vaja
> > <RAJANV@xilinx.com>
> > Subject: Re: [PATCH v3 2/4] drivers: firmware: xilinx: Add ZynqMP firmware
> > driver
> >
> > On Wed, Jan 24, 2018 at 03:21:12PM -0800, Jolly Shah wrote:
> > > This patch is adding communication layer with firmware.
> > > Firmware driver provides an interface to firmware APIs.
> > > Interface APIs can be used by any driver to communicate to
> > > PMUFW(Platform Management Unit). All requests go through ATF.
> >
> > > +/**
> > > + * zynqmp_pm_set_wakeup_source - PM call to specify the wakeup source
> > > + * while suspended
> > > + * @target: Node ID of the targeted PU or subsystem
> > > + * @wakeup_node:Node ID of the wakeup peripheral
> > > + * @enable: Enable or disable the specified peripheral as wake source
> > > + *
> > > + * Return: Returns status, either success or error+reason
> > > + */
> > > +static int zynqmp_pm_set_wakeup_source(const u32 target,
> > > + const u32 wakeup_node,
> > > + const u32 enable)
> > > +{
> > > + return invoke_pm_fn(PM_SET_WAKEUP_SOURCE, target,
> > > + wakeup_node, enable, 0, NULL); }
> >
> > I see many functions take a "Node ID" parameter, but these don't appear to be
> > in any DT binding, and drivers (other than the debugfs driver) aren't using them.
> >
> > What's the plan for making use of these? Where are the node IDs going to come
> > from in practice?
> >
> Node ids are defined in firmware.h. Node id refers to targeted PU/subsystem/peripheral for required action.

Ok. What I was asking was how a node id would be associated with
particular peripheral instances (which are presumably going to be nodes
in the DT).

e.g. if I have

device@foo {
compatible = "xlnx,some-device";
reg = <0xf00 0x100>;
...
};

... how does the kernel know which node id(s) the device is associated
with?

I assume that those will need something like a xlnx,eemi-node-id
property.

[...]

> > > +/**
> > > + * zynqmp_pm_pinctrl_request - Request Pin from firmware
> > > + * @pin: Pin number to request
> > > + *
> >
> > No DT binding for the pinctrl bits?
> >
> > [...]
> It doesn't require any bindings. Calling drivers will have DT binding for pins they use.

For those drivers to be able to refer to the EEMI FW as a pin
controller, we'll need a pinctrl node in the DT (and hence a binding).

> > > +/**
> > > + * zynqmp_pm_clock_enable - Enable the clock for given id
> > > + * @clock_id: ID of the clock to be enabled
> > > + *
> >
> > Likewise for the clocks?
> >
> It doesn't require bindings too.

As with pinctrl, for drivers to be able to refer to these clocks, we'll
need a clock node in the DT (and hence a binding).

Thanks,
Mark.

\
 
 \ /
  Last update: 2018-02-01 11:33    [W:0.919 / U:0.160 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site