lkml.org 
[lkml]   [2018]   [Dec]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 2/3] arm64: dts: allwinner: a64: Add A64 CSI controller
Hi Maxime

On Fri, Dec 7, 2018 at 8:47 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> On Thu, Dec 06, 2018 at 06:07:59PM +0100, Michael Nazzareno Trimarchi wrote:
> > On Thu, Dec 6, 2018 at 4:34 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
> > > On Thu, Dec 06, 2018 at 06:53:05PM +0530, Jagan Teki wrote:
> > > > Allwinner A64 CSI controller has similar features as like in
> > > > H3, So add support for A64 via H3 fallback.
> > > >
> > > > Also updated CSI_SCLK to use 300MHz via assigned-clocks, since
> > > > the default clock 600MHz seems unable to drive the sensor(ov5640)
> > > > to capture the image.
> > > >
> > > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > > > ---
> > > > Changes for v2:
> > > > - Use CSI_SCLK to 300MHz
> > > >
> > > > arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 23 +++++++++++++++++++
> > > > 1 file changed, 23 insertions(+)
> > > >
> > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> > > > index 384c417cb7a2..d7ab0006ebce 100644
> > > > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> > > > @@ -532,6 +532,12 @@
> > > > interrupt-controller;
> > > > #interrupt-cells = <3>;
> > > >
> > > > + csi_pins: csi-pins {
> > > > + pins = "PE0", "PE2", "PE3", "PE4", "PE5", "PE6",
> > > > + "PE7", "PE8", "PE9", "PE10", "PE11";
> > > > + function = "csi0";
> > > > + };
> > > > +
> > > > i2c0_pins: i2c0_pins {
> > > > pins = "PH0", "PH1";
> > > > function = "i2c0";
> > > > @@ -899,6 +905,23 @@
> > > > status = "disabled";
> > > > };
> > > >
> > > > + csi: csi@1cb0000 {
> > > > + compatible = "allwinner,sun50i-a64-csi",
> > > > + "allwinner,sun8i-h3-csi";
> > > > + reg = <0x01cb0000 0x1000>;
> > > > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > > > + clocks = <&ccu CLK_BUS_CSI>,
> > > > + <&ccu CLK_CSI_SCLK>,
> > > > + <&ccu CLK_DRAM_CSI>;
> > > > + clock-names = "bus", "mod", "ram";
> > > > + resets = <&ccu RST_BUS_CSI>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&csi_pins>;
> > > > + assigned-clocks = <&ccu CLK_CSI_SCLK>;
> > > > + assigned-clock-rates = <300000000>;
> > >
> > > That should be enforced in the driver.
> > >
> >
> > We are not really sure what is the best here. Our first idea was to
> > put in the board file and then Jagan
> > decide to put in dtsi. We don't have enough coverage of camera on this
> > CPU and I prefer to stay with this
> > minimal change that does not impact the driver.
>
> The thing is that:
> - in this commit log, you're stating that it depends on the sensor,
> which indicates that this would be a board level addition
> - In another patch series, Jagan reported IIRC that it actually
> depends on the resolution, so it doesn't belong in the DT at all
> - And then, you don't even have any guarantee on the clock rate. The
> sole guarantee you have is that when your driver will probe, the
> rate will be close to those 300MHz. That's it. It might completely
> change after the driver has probed, or be rounded to something
> else entirely, who knows.

I'm not so interested in the story but it's clear what you ask but in
short having one
sensor up to 5M pixel we can be sure where the reason is but make it
more pratical.

We have a parent clock that is the peripheral clock on clock
tree that run at 600Mhz. With a clock divider of 0 the driver work but
the acquisition
as problem on quality. Now the same sensor seems to work when the
logic is clocked
as half of the speed. If I remind in the right way the divider can be
only possible so
you can get pclk / (n + 1) without reparent to a different input.
Now I don't find any nice documentation that state that 600Mhz
is not supported but anyway, you suggest to do the same that is done
in fimc driver so
set there the rate there and offcourse x platform change like:

#define A64_CSI_FREQUENCY 600

ret = clk_set_rate(csk_core_clk, A64_CSI_FREQUENCY);

>
> So really, putting it in the DT is nothing but a hack.
>

Michael


> Maxime
>
> --
> Maxime Ripard, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com



--
| Michael Nazzareno Trimarchi Amarula Solutions BV |
| COO - Founder Cruquiuskade 47 |
| +31(0)851119172 Amsterdam 1018 AM NL |
| [`as] http://www.amarulasolutions.com |

\
 
 \ /
  Last update: 2018-12-07 10:17    [W:0.072 / U:0.708 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site