lkml.org 
[lkml]   [2018]   [Dec]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/3] dt-bindings: bus: imx-weim: document multiple address ranges per child node
Date
The imx-weim driver was patched to allow correct WEIM configuration
when multiple address ranges are used in a child node.
Update the dt-bindings to reflect this.

Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
---
.../devicetree/bindings/bus/imx-weim.txt | 32 +++++++++++++++++--
1 file changed, 29 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt
index 683eaf3aed79..dda7d6d66479 100644
--- a/Documentation/devicetree/bindings/bus/imx-weim.txt
+++ b/Documentation/devicetree/bindings/bus/imx-weim.txt
@@ -47,9 +47,9 @@ Optional properties:
Timing property for child nodes. It is mandatory, not optional.

- fsl,weim-cs-timing: The timing array, contains timing values for the
- child node. We can get the CS index from the child
- node's "reg" property. The number of registers depends
- on the selected chip.
+ child node. We get the CS indexes from the address
+ ranges in the child node's "reg" property.
+ The number of registers depends on the selected chip:
For i.MX1, i.MX21 ("fsl,imx1-weim") there are two
registers: CSxU, CSxL.
For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim")
@@ -80,3 +80,29 @@ Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
0x0000c000 0x1404a38e 0x00000000>;
};
};
+
+Example for an imx6q-based board, a multi-chipselect device connected to WEIM:
+
+In this case, both chip select 0 and 1 will be configured with the same timing
+array values.
+
+ weim: weim@21b8000 {
+ compatible = "fsl,imx6q-weim";
+ reg = <0x021b8000 0x4000>;
+ clocks = <&clks 196>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x02000000
+ 1 0 0x0a000000 0x02000000
+ 2 0 0x0c000000 0x02000000
+ 3 0 0x0e000000 0x02000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+
+ acme@0 {
+ compatible = "acme,whatever";
+ reg = <0 0 0x100>, <0 0x400000 0x800>,
+ <1 0x400000 0x800>;
+ fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
+ 0x00000000 0xa0000240 0x00000000>;
+ };
+ };
--
2.17.1
\
 
 \ /
  Last update: 2018-12-06 20:27    [W:0.047 / U:8.992 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site