lkml.org 
[lkml]   [2018]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/3] clk: sunxi-ng: a33: Use sigma-delta modulation for audio PLL
Date
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.

The vendor kernel gets around this (for newer SoCs) by using sigma-delta
modulation to generate a fractional-N factor. As the PLL hardware is
identical in most chips, we can back port the settings from the newer
SoC, in this case the H3, onto the A33.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 37 ++++++++++++++++++----------
1 file changed, 24 insertions(+), 13 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
index 13eb5b23c5e7..f763648a5f20 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
@@ -51,18 +51,29 @@ static struct ccu_nkmp pll_cpux_clk = {
* the base (2x, 4x and 8x), and one variable divider (the one true
* pll audio).
*
- * We don't have any need for the variable divider for now, so we just
- * hardcode it to match with the clock names
+ * With sigma-delta modulation for fractional-N on the audio PLL,
+ * we have to use specific dividers. This means the variable divider
+ * can no longer be used, as the audio codec requests the exact clock
+ * rates we support through this mechanism. So we now hard code the
+ * variable divider to 1. This means the clock rates will no longer
+ * match the clock names.
*/
#define SUN8I_A33_PLL_AUDIO_REG 0x008

-static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
- "osc24M", 0x008,
- 8, 7, /* N */
- 0, 5, /* M */
- BIT(31), /* gate */
- BIT(28), /* lock */
- CLK_SET_RATE_UNGATE);
+static struct ccu_sdm_setting pll_audio_sdm_table[] = {
+ { .rate = 22579200, .pattern = 0xc0010d84, .m = 8, .n = 7 },
+ { .rate = 24576000, .pattern = 0xc000ac02, .m = 14, .n = 14 },
+};
+
+static SUNXI_CCU_NM_WITH_SDM_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
+ "osc24M", 0x008,
+ 8, 7, /* N */
+ 0, 5, /* M */
+ pll_audio_sdm_table, BIT(24),
+ 0x284, BIT(31),
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ CLK_SET_RATE_UNGATE);

static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video_clk, "pll-video",
"osc24M", 0x010,
@@ -576,9 +587,9 @@ static struct ccu_common *sun8i_a33_ccu_clks[] = {
&ats_clk.common,
};

-/* We hardcode the divider to 4 for now */
+/* We hardcode the divider to 1 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
- "pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
+ "pll-audio-base", 1, 1, CLK_SET_RATE_PARENT);
static CLK_FIXED_FACTOR(pll_audio_2x_clk, "pll-audio-2x",
"pll-audio-base", 2, 1, CLK_SET_RATE_PARENT);
static CLK_FIXED_FACTOR(pll_audio_4x_clk, "pll-audio-4x",
@@ -781,10 +792,10 @@ static void __init sun8i_a33_ccu_setup(struct device_node *node)
return;
}

- /* Force the PLL-Audio-1x divider to 4 */
+ /* Force the PLL-Audio-1x divider to 1 */
val = readl(reg + SUN8I_A33_PLL_AUDIO_REG);
val &= ~GENMASK(19, 16);
- writel(val | (3 << 16), reg + SUN8I_A33_PLL_AUDIO_REG);
+ writel(val | (0 << 16), reg + SUN8I_A33_PLL_AUDIO_REG);

/* Force PLL-MIPI to MIPI mode */
val = readl(reg + SUN8I_A33_PLL_MIPI_REG);
--
2.20.0.rc1
\
 
 \ /
  Last update: 2018-12-05 11:13    [W:0.330 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site