lkml.org 
[lkml]   [2018]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] soc: renesas: rcar-sysc: Fix power domain control after system resume
On Wed, Dec 05, 2018 at 04:39:45PM +0100, Geert Uytterhoeven wrote:
> To control power to a power domain, the System Controller (SYSC) needs
> the corresponding interrupt source to be enabled, but masked, to prevent
> the CPU from receiving it.
>
> Currently this is handled in the driver's probe() routine, and set up
> for every domain present, even if it will not be controlled directly by
> SYSC (CPU domains are powered through the APMU on R-Car Gen2 and later).
>
> On R-Car Gen3, PSCI powers down the SoC during system suspend, thus
> loosing any configured interrupt state. Hence after system resume, power
> domains not controlled through the APMU (e.g. A3IR, A3VC, A3VP) fail to
> power up.

I corrected the spelling of losing when applying this patch.

>
> Fix this by replacing the global interrupt setup in the probe() routine
> by a domain-specific interrupt setup in rcar_sysc_power(), where the
> domain's power is actually controlled. This brings the code more in
> line with the flowchart in the Hardware User's Manual.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> ---
> drivers/soc/renesas/rcar-sysc.c | 28 +++++++++-------------------
> 1 file changed, 9 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/soc/renesas/rcar-sysc.c b/drivers/soc/renesas/rcar-sysc.c
> index 123e553510e826f5..0c80fab4f8de6bc8 100644
> --- a/drivers/soc/renesas/rcar-sysc.c
> +++ b/drivers/soc/renesas/rcar-sysc.c
> @@ -105,6 +105,15 @@ static int rcar_sysc_power(const struct rcar_sysc_ch *sysc_ch, bool on)
>
> spin_lock_irqsave(&rcar_sysc_lock, flags);
>
> + /*
> + * The interrupt source needs to be enabled, but masked, to prevent the
> + * CPU from receiving it.
> + */
> + iowrite32(ioread32(rcar_sysc_base + SYSCIMR) | isr_mask,
> + rcar_sysc_base + SYSCIMR);
> + iowrite32(ioread32(rcar_sysc_base + SYSCIER) | isr_mask,
> + rcar_sysc_base + SYSCIER);
> +
> iowrite32(isr_mask, rcar_sysc_base + SYSCISCR);
>
> /* Submit power shutoff or resume request until it was accepted */
> @@ -324,7 +333,6 @@ static int __init rcar_sysc_pd_init(void)
> const struct of_device_id *match;
> struct rcar_pm_domains *domains;
> struct device_node *np;
> - u32 syscier, syscimr;
> void __iomem *base;
> unsigned int i;
> int error;
> @@ -363,24 +371,6 @@ static int __init rcar_sysc_pd_init(void)
> domains->onecell_data.num_domains = ARRAY_SIZE(domains->domains);
> rcar_sysc_onecell_data = &domains->onecell_data;
>
> - for (i = 0, syscier = 0; i < info->num_areas; i++)
> - syscier |= BIT(info->areas[i].isr_bit);
> -
> - /*
> - * Mask all interrupt sources to prevent the CPU from receiving them.
> - * Make sure not to clear reserved bits that were set before.
> - */
> - syscimr = ioread32(base + SYSCIMR);
> - syscimr |= syscier;
> - pr_debug("%pOF: syscimr = 0x%08x\n", np, syscimr);
> - iowrite32(syscimr, base + SYSCIMR);
> -
> - /*
> - * SYSC needs all interrupt sources enabled to control power.
> - */
> - pr_debug("%pOF: syscier = 0x%08x\n", np, syscier);
> - iowrite32(syscier, base + SYSCIER);
> -
> for (i = 0; i < info->num_areas; i++) {
> const struct rcar_sysc_area *area = &info->areas[i];
> struct rcar_sysc_pd *pd;
> --
> 2.17.1
>

\
 
 \ /
  Last update: 2018-12-05 22:22    [W:0.089 / U:0.736 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site