lkml.org 
[lkml]   [2018]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 5/5] arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node
On Mon, Dec 3, 2018 at 6:08 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> Amarula A64-Relic board by default bound with OV5640 camera,
> so add support for it with below pin information.
>
> - PE13, PE12 via i2c-gpio bitbanging
> - CLK_CSI_MCLK as external clock
> - PE1 as external clock pin muxing
> - DLDO3 as vcc-csi supply
> - DLDO3 as AVDD supply
> - ALDO1 as DOVDD supply
> - ELDO3 as DVDD supply
> - PE14 gpio for reset pin
> - PE15 gpio for powerdown pin
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> .../allwinner/sun50i-a64-amarula-relic.dts | 54 +++++++++++++++++++
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 5 ++
> 2 files changed, 59 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
> index 6cb2b7f0c817..9ac6d773188b 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
> @@ -22,6 +22,41 @@
> stdout-path = "serial0:115200n8";
> };
>
> + i2c-csi {
> + compatible = "i2c-gpio";
> + sda-gpios = <&pio 4 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> + scl-gpios = <&pio 4 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;

FYI our hardware doesn't do open drain.

> + i2c-gpio,delay-us = <5>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ov5640: camera@3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&csi_mclk_pin>;
> + clocks = <&ccu CLK_CSI_MCLK>;
> + clock-names = "xclk";
> +
> + AVDD-supply = <&reg_dldo3>;
> + DOVDD-supply = <&reg_aldo1>;

DOVDD is the supply for I/O. You say it is ALDO1 here.

> + DVDD-supply = <&reg_eldo3>;
> + reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* CSI-RST-R: PE14 */
> + powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */
> +
> + port {
> + ov5640_ep: endpoint {
> + remote-endpoint = <&csi_ep>;
> + bus-width = <8>;
> + hsync-active = <1>; /* Active high */
> + vsync-active = <0>; /* Active low */
> + data-active = <1>; /* Active high */
> + pclk-sample = <1>; /* Rising */
> + };
> + };
> + };
> + };
> +
> wifi_pwrseq: wifi-pwrseq {
> compatible = "mmc-pwrseq-simple";
> clocks = <&rtc 1>;
> @@ -30,6 +65,25 @@
> };
> };
>
> +&csi {
> + vcc-csi-supply = <&reg_dldo3>;

But here you say the SoC-side pins are driven from DLDO3.

This is a somewhat odd mismatch.

Regardless, the ov5640 driver enables all three regulators at probe time.
Shouldn't that be enough to get the I2C bus working? The pin voltage
supply does not belong here.

> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + csi_ep: endpoint {
> + remote-endpoint = <&ov5640_ep>;
> + bus-width = <8>;
> + hsync-active = <1>; /* Active high */
> + vsync-active = <0>; /* Active low */
> + data-active = <1>; /* Active high */
> + pclk-sample = <1>; /* Rising */
> + };
> + };
> +};
> +
> &ehci0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index d32ff694ac5c..844bb44a78af 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -538,6 +538,11 @@
> function = "csi0";
> };
>
> + csi_mclk_pin: csi-mclk {
> + pins = "PE1";
> + function = "csi0";
> + };
> +

This should be a separate patch.

ChenYu

> i2c0_pins: i2c0_pins {
> pins = "PH0", "PH1";
> function = "i2c0";
> --
> 2.18.0.321.gffc6fa0e3
>

\
 
 \ /
  Last update: 2018-12-03 11:25    [W:0.130 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site