lkml.org 
[lkml]   [2018]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] pinctrl: meson: fix G12A ao pull registers base address
From
Date


On 2018/12/3 18:27, Neil Armstrong wrote:
> Hi Xingyu,
>
>
> On 03/12/2018 04:05, Xingyu Chen wrote:
>> Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG
>> and AO_GPIO_O.
>>
>> These bits of controlling output level are remapped to the new register
>> AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable.
>>
>> These bits of controlling pull enable are remapped to the new register
>> AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling
>> pull type(up/down).
>>
>> The new layout of ao gpio/pull registers is as follows:
>> - AO_GPIO_O_EN_N [offset: 0x9 << 2]
>> - AO_GPIO_I [offset: 0xa << 2]
>> - AO_RTI_PULL_UP_REG [offset: 0xb << 2]
>> - AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2]
>> - AO_GPIO_O [offset: 0xd << 2]
>>
>> From above, we can see ao GPIO registers region has been separated by the
>> ao pull registers. In order to ensure the continuity of the region on
>> software, the ao GPIO and ao pull registers use the same base address, but
>> can be identified by the offset.
>>
>> Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support")
>> Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
>> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
>> ---
>> drivers/pinctrl/meson/pinctrl-meson.c | 22 ++++++++++++----------
>> 1 file changed, 12 insertions(+), 10 deletions(-)
>>
>> diff --git a/drivers/pinctrl/meson/pinctrl-meson.c b/drivers/pinctrl/meson/pinctrl-meson.c
>> index 53d449076dee..7ff40cd7a0cb 100644
>> --- a/drivers/pinctrl/meson/pinctrl-meson.c
>> +++ b/drivers/pinctrl/meson/pinctrl-meson.c
>> @@ -31,6 +31,9 @@
>> * In some cases the register ranges for pull enable and pull
>> * direction are the same and thus there are only 3 register ranges.
>> *
>> + * Since Meson G12A SoC, the ao register ranges for gpio, pull enable
>> + * and pull direction are the same, so there are only 2 register ranges.
>> + *
>> * For the pull and GPIO configuration every bank uses a contiguous
>> * set of bits in the register sets described above; the same register
>> * can be shared by more banks with different offsets.
>> @@ -487,23 +490,22 @@ static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc,
>> return PTR_ERR(pc->reg_mux);
>> }
>>
>> - pc->reg_pull = meson_map_resource(pc, gpio_np, "pull");
>> - if (IS_ERR(pc->reg_pull)) {
>> - dev_err(pc->dev, "pull registers not found\n");
>> - return PTR_ERR(pc->reg_pull);
>> + pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio");
>> + if (IS_ERR(pc->reg_gpio)) {
>> + dev_err(pc->dev, "gpio registers not found\n");
>> + return PTR_ERR(pc->reg_gpio);
>> }
>>
>> + pc->reg_pull = meson_map_resource(pc, gpio_np, "pull");
>> + /* Use gpio region if pull one is not present */
>> + if (IS_ERR(pc->reg_pull))
>> + pc->reg_pull = pc->reg_gpio;
>> +
>> pc->reg_pullen = meson_map_resource(pc, gpio_np, "pull-enable");
>> /* Use pull region if pull-enable one is not present */
>> if (IS_ERR(pc->reg_pullen))
>> pc->reg_pullen = pc->reg_pull;
>>
>> - pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio");
>> - if (IS_ERR(pc->reg_gpio)) {
>> - dev_err(pc->dev, "gpio registers not found\n");
>> - return PTR_ERR(pc->reg_gpio);
>> - }
>> -
>> return 0;
>> }
>>
>>
> Doesn't it need an update of the bindings ?
>
> Neil
>
Thanks, I will update it in next patch
> .
>

\
 
 \ /
  Last update: 2018-12-04 03:05    [W:0.082 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site