lkml.org 
[lkml]   [2018]   [Dec]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 11/12] drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
On Fri, Dec 14, 2018 at 04:35:11PM +0530, Jagan Teki wrote:
> On Fri, Dec 14, 2018 at 1:25 AM Sean Paul <sean@poorly.run> wrote:
> >
> > On Fri, Dec 14, 2018 at 12:56:03AM +0530, Jagan Teki wrote:
> > > On Thu, Dec 13, 2018 at 8:37 PM Sean Paul <sean@poorly.run> wrote:
> > > >
> > > > On Fri, Nov 16, 2018 at 10:09:15PM +0530, Jagan Teki wrote:
> > > > > Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
> > > > >
> > > > > Add panel driver for it.
> > > > >
> > > > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > > > > ---
> > > > > MAINTAINERS | 6 +
> > > > > drivers/gpu/drm/panel/Kconfig | 9 +
> > > > > drivers/gpu/drm/panel/Makefile | 1 +
> > > > > .../drm/panel/panel-feiyang-fy07024di26a30d.c | 286 ++++++++++++++++++
> > > > > 4 files changed, 302 insertions(+)
> > > > > create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
> > > > >
> >
> > /snip
> >
> > > > > diff --git a/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c b/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
> > > > > new file mode 100644
> > > > > index 000000000000..a4b46bd8fdbe
> > > > > --- /dev/null
> > > > > +++ b/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
> >
> > /snip
> >
> > > > > +static int feiyang_prepare(struct drm_panel *panel)
> > > > > +{
> > > > > + struct feiyang *ctx = panel_to_feiyang(panel);
> > > > > + struct mipi_dsi_device *dsi = ctx->dsi;
> > > > > + unsigned int i;
> > > > > + int ret;
> > > > > +
> > > > > + ret = regulator_enable(ctx->dvdd);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + msleep(100);
> > > >
> > > > nit: You should do your best to correlate the sleeps with the timing parameters
> > > > from the datasheet with a comment.
> > > >
> > > > ie:
> > > > /* T1: > 100ms */
> > > > msleep(100);
> > >
> > > Sorry, what does this mean?
> >
> > On page 9 of the datasheet you sent me [1], it has the delays required to safely
> > power up the panel. This delay is the time between dvdd going high and avdd
> > going high. On the figure in the datasheet, this would be T2 (T1 is dvdd rise
>
> time between dvdd going high and avdd going high is T1 + T3 right?
>
> T2 > 0ms
> T3 > 20ms
>
> In this case the delay can be msleep(20) ?

Hmm, yeah, I didn't notice that T3 was > 20ms, that's kind of confusing. So I
think you're right, this should be T2 + T3 > 20ms (T1 is covered in the
regulator_enable of dvdd).

>
> > time and should be handled in the regulator subsystem (iirc)). Also according to
> > the datasheet, T2 just needs to be > 0, so you don't even need this delay. You
> > could replace this with a comment like:
> >
> > /* T1 (dvdd rise time) + T2 (dvdd->avdd) > 0 */
> >
> > So for all of the msleeps below you should get the delays from the datasheet and
> > add a comment referencing them.
>
> T5 and T6 are delay between avdd to reset enable it can be 10 + 10
> =&gt; 20ms and finally T12 which is 200 after reset.
>
> What about the delay between resets, I need to understand it a bit.

These are usually accounted for at the end of disable. Take a look at the sleep
parameters in panel-simple for an example.

Sean

--
Sean Paul, Software Engineer, Google / Chromium OS

\
 
 \ /
  Last update: 2018-12-14 15:16    [W:1.118 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site