lkml.org 
[lkml]   [2018]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 3/3] spi: meson-axg: add a linear clock divider support
From
Date
On Thu, 2018-12-13 at 09:55 +0100, Neil Armstrong wrote:
> Hi Sunny,
>
> On 13/12/2018 09:39, Sunny Luo wrote:
> > The SPICC controller in Meson-AXG SoC is capable of using
> > a linear clock divider to reach a much fine tuned range of clocks,
> > while the old controller only use a power of two clock divider,
> > result at a more coarse clock range.
>
> This patch should definitely go before patch 1.
>
> > Also convert the clock registration into Common Clock Framework.
> >
> > Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
> > Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> > ---
> > drivers/spi/Kconfig | 2 +-
> > drivers/spi/spi-meson-spicc.c | 209 ++++++++++++++++++++++++++++++++++---
> > -----
> > 2 files changed, 170 insertions(+), 41 deletions(-)
> >
> > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> > index 9f89cb1..75f7362 100644
> > --- a/drivers/spi/Kconfig
> > +++ b/drivers/spi/Kconfig
> > @@ -384,7 +384,7 @@ config SPI_FSL_ESPI
> >
> > config SPI_MESON_SPICC
> > tristate "Amlogic Meson SPICC controller"
> > - depends on ARCH_MESON || COMPILE_TEST
> > + depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST)

The purpose of this patch is clock, right ? Why does it add a dependency on OF
?

> > help
> > This enables master mode support for the SPICC (SPI communication
> > controller) available in Amlogic Meson SoCs.
> > diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
> > index 0384c28..59af18e 100644
> > --- a/drivers/spi/spi-meson-spicc.c
> > +++ b/drivers/spi/spi-meson-spicc.c
> > @@ -116,6 +116,9 @@
> > #define SPICC_DWADDR 0x24 /* Write Address of DMA */
> >
> > #define SPICC_ENH_CTL0 0x38 /* Enhanced Feature */
> > +#define SPICC_ENH_CLK_CS_DELAY_MASK GENMASK(15, 0)
> > +#define SPICC_ENH_DATARATE_MASK GENMASK(23, 16)
> > +#define SPICC_ENH_DATARATE_EN BIT(24)
> > #define SPICC_ENH_MOSI_OEN BIT(25)
> > #define SPICC_ENH_CLK_OEN BIT(26)
> > #define SPICC_ENH_CS_OEN BIT(27)
> > @@ -131,6 +134,7 @@
> > struct meson_spicc_data {
> > unsigned int max_speed_hz;
> > bool has_oen;
> > + bool has_enhance_clk_div;
> > };
> >
> > struct meson_spicc_device {
> > @@ -138,6 +142,7 @@ struct meson_spicc_device {
> > struct platform_device *pdev;
> > void __iomem *base;
> > struct clk *core;
> > + struct clk *clk;
> > struct spi_message *message;
> > struct spi_transfer *xfer;
> > const struct meson_spicc_data *data;
> > @@ -325,40 +330,6 @@ static irqreturn_t meson_spicc_irq(int irq, void
> > *data)
> > return IRQ_HANDLED;
> > }
> >
> > -static u32 meson_spicc_setup_speed(struct meson_spicc_device *spicc, u32
> > conf,
> > - u32 speed)
> > -{
> > - unsigned long parent, value;
> > - unsigned int i, div;
> > -
> > - parent = clk_get_rate(spicc->core);
> > -
> > - /* Find closest inferior/equal possible speed */
> > - for (i = 0 ; i < 7 ; ++i) {
> > - /* 2^(data_rate+2) */
> > - value = parent >> (i + 2);
> > -
> > - if (value <= speed)
> > - break;
> > - }
> > -
> > - /* If provided speed it lower than max divider, use max divider */
> > - if (i > 7) {
> > - div = 7;
> > - dev_warn_once(&spicc->pdev->dev, "unable to get close to speed
> > %u\n",
> > - speed);
> > - } else
> > - div = i;
> > -
> > - dev_dbg(&spicc->pdev->dev, "parent %lu, speed %u -> %lu (%u)\n",
> > - parent, speed, value, div);
> > -
> > - conf &= ~SPICC_DATARATE_MASK;
> > - conf |= FIELD_PREP(SPICC_DATARATE_MASK, div);
> > -
> > - return conf;
> > -}
> > -
> > static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
> > struct spi_transfer *xfer)
> > {
> > @@ -367,9 +338,6 @@ static void meson_spicc_setup_xfer(struct
> > meson_spicc_device *spicc,
> > /* Read original configuration */
> > conf = conf_orig = readl_relaxed(spicc->base + SPICC_CONREG);
> >
> > - /* Select closest divider */
> > - conf = meson_spicc_setup_speed(spicc, conf, xfer->speed_hz);
> > -
> > /* Setup word width */
> > conf &= ~SPICC_BITLENGTH_MASK;
> > conf |= FIELD_PREP(SPICC_BITLENGTH_MASK,
> > @@ -378,6 +346,8 @@ static void meson_spicc_setup_xfer(struct
> > meson_spicc_device *spicc,
> > /* Ignore if unchanged */
> > if (conf != conf_orig)
> > writel_relaxed(conf, spicc->base + SPICC_CONREG);
> > +
> > + clk_set_rate(spicc->clk, xfer->speed_hz);
> > }
> >
> > static int meson_spicc_transfer_one(struct spi_master *master,
> > @@ -486,9 +456,6 @@ static int meson_spicc_unprepare_transfer(struct
> > spi_master *master)
> > /* Disable all IRQs */
> > writel(0, spicc->base + SPICC_INTREG);
> >
> > - /* Disable controller */
> > - writel_bits_relaxed(SPICC_ENABLE, 0, spicc->base + SPICC_CONREG);
> > -
> > device_reset_optional(&spicc->pdev->dev);
> >
> > return 0;
> > @@ -528,6 +495,157 @@ static void meson_spicc_cleanup(struct spi_device
> > *spi)
> > spi->controller_state = NULL;
> > }
> >
> > +/*
> > + * The Clock Mux
> > + * x-----------------x x------------x x------\
> > + * |---| 0) fixed factor |---| 1) old div |----| |
> > + * | x-----------------x x------------x | |
> > + * src ---| |5) mux|-- out
> > + * | x-----------------x x------------x | |
> > + * |---| 2) fixed factor |---| 3) new div |0---| |
> > + * x-----------------x x------------x x------/
> > + *
> > + * Clk path for GX series:
> > + * src -> 0 -> 1 -> out
> > + *
> > + * Clk path for AXG series:
> > + * src -> 0 -> 1 -> 5 -> out
> > + * src -> 2 -> 3 -> 5 -> out
> > + */
> > +
> > +/* algorithm for div0 + div1: rate = freq / 4 / (2 ^ N) */
> > +static struct clk_fixed_factor meson_spicc_div0 = {
> > + .mult = 1,
> > + .div = 4,
> > +};
> > +
> > +static struct clk_divider meson_spicc_div1 = {
> > + .reg = (void *)SPICC_CONREG,
> > + .shift = 16,
> > + .width = 3,
> > + .flags = CLK_DIVIDER_POWER_OF_TWO,
> > +};
> > +
> > +/* algorithm for div2 + div3: rate = freq / 2 / (N + 1) */
> > +static struct clk_fixed_factor meson_spicc_div2 = {
> > + .mult = 1,
> > + .div = 2,
> > +};
> > +
> > +static struct clk_divider meson_spicc_div3 = {
> > + .reg = (void *)SPICC_ENH_CTL0,
> > + .shift = 16,
> > + .width = 8,
> > +};
> > +
> > +static struct clk_mux meson_spicc_sel = {
> > + .reg = (void *)SPICC_ENH_CTL0,
> > + .mask = 0x1,
> > + .shift = 24,
> > +};
> > +
> > +static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
> > +{
> > + struct device *dev = &spicc->pdev->dev;
> > + struct clk_fixed_factor *div0;
> > + struct clk_divider *div1;

Could you come up with something better than div0 and div1 ? it is confusing,
especially with the comment above about div3 and 4 ... fixed_factor, div maybe
?

> > + struct clk_mux *mux;
> > + struct clk_init_data init;
> > + struct clk *clk;
> > + const char *parent_names[1];
> > + const char *mux_parent_names[2];
> > + char name[32];
> > +
> > + div0 = &meson_spicc_div0;
> > + snprintf(name, sizeof(name), "%s#_div0", dev_name(dev));
> > + init.name = name;
> > + init.ops = &clk_fixed_factor_ops;
> > + init.flags = 0;
> > + parent_names[0] = __clk_get_name(spicc->core);
> > + init.parent_names = parent_names;
> > + init.num_parents = 1;
> > +
> > + div0->hw.init = &init;
> > +
> > + clk = devm_clk_register(dev, &div0->hw);
> > + if (WARN_ON(IS_ERR(clk)))
> > + return PTR_ERR(clk);
> > +
> > + div1 = &meson_spicc_div1;
> > + snprintf(name, sizeof(name), "%s#_div1", dev_name(dev));
> > + init.name = name;
> > + init.ops = &clk_divider_ops;
> > + init.flags = CLK_SET_RATE_PARENT;
> > + parent_names[0] = __clk_get_name(clk);
> > + init.parent_names = parent_names;
> > + init.num_parents = 1;
> > +
> > + div1->reg = spicc->base + (u64)div1->reg;

So you have static data which you override here. This works only if there is a
single instance ... and does not really improve readability in your case.

IMO, you'd be better off without the static data above.

> > + div1->hw.init = &init;
> > +
> > + clk = devm_clk_register(dev, &div1->hw);
> > + if (WARN_ON(IS_ERR(clk)))
> > + return PTR_ERR(clk);
> > +
> > + if (!spicc->data->has_enhance_clk_div) {

Do all SoC with 'has_oen' have 'has_enhance_clk_div' too ?
DO you really need two flags ?

> > + spicc->clk = clk;
> > + return 0;
> > + }
> > +
> > + mux_parent_names[0] = __clk_get_name(clk);
> > +
> > + div0 = &meson_spicc_div2;
> > + snprintf(name, sizeof(name), "%s#_div2", dev_name(dev));
> > + init.name = name;
> > + init.ops = &clk_fixed_factor_ops;
> > + init.flags = 0;
> > + parent_names[0] = __clk_get_name(spicc->core);
> > + init.parent_names = parent_names;
> > + init.num_parents = 1;
> > +
> > + div0->hw.init = &init;
> > +
> > + clk = devm_clk_register(dev, &div0->hw);
> > + if (WARN_ON(IS_ERR(clk)))
> > + return PTR_ERR(clk);
> > +
> > + div1 = &meson_spicc_div3;
> > + snprintf(name, sizeof(name), "%s#_div3", dev_name(dev));
> > + init.name = name;
> > + init.ops = &clk_divider_ops;
> > + init.flags = CLK_SET_RATE_PARENT;
> > + parent_names[0] = __clk_get_name(clk);
> > + init.parent_names = parent_names;
> > + init.num_parents = 1;
> > +
> > + div1->reg = spicc->base + (u64)div1->reg;
> > + div1->hw.init = &init;
> > +
> > + clk = devm_clk_register(dev, &div1->hw);
> > + if (WARN_ON(IS_ERR(clk)))
> > + return PTR_ERR(clk);
> > +
> > + mux_parent_names[1] = __clk_get_name(clk);
> > +
> > + mux = &meson_spicc_sel;
> > + snprintf(name, sizeof(name), "%s#_sel", dev_name(dev));
> > + init.name = name;
> > + init.ops = &clk_mux_ops;
> > + init.parent_names = mux_parent_names;
> > + init.num_parents = 2;
> > + init.flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT;

Why CLK_SET_RATE_NO_REPARENT ? CCF should pick the parent that give the best
results, best to let it do its task ...

> > +
> > + mux->reg = spicc->base + (u64)mux->reg;
> > + mux->hw.init = &init;
> > +
> > + spicc->clk = devm_clk_register(dev, &mux->hw);
> > + if (WARN_ON(IS_ERR(spicc->clk)))
> > + return PTR_ERR(spicc->clk);
> > +
> > + clk_set_parent(spicc->clk, clk);

... then you can drop this.

> > + return 0;
> > +}
>
> I'll let Jerome review this !
>
> > +
> > static int meson_spicc_probe(struct platform_device *pdev)
> > {
> > struct spi_master *master;
> > @@ -557,6 +675,10 @@ static int meson_spicc_probe(struct platform_device
> > *pdev)
> > goto out_master;
> > }
> >
> > + /* Set master mode and enable controller */
> > + writel_relaxed(SPICC_ENABLE | SPICC_MODE_MASTER,
> > + spicc->base + SPICC_CONREG);
>
> Please remove it from meson_spicc_prepare_message() now.
>
> > +
> > /* Disable all IRQs */
> > writel_relaxed(0, spicc->base + SPICC_INTREG);
> >
> > @@ -603,6 +725,12 @@ static int meson_spicc_probe(struct platform_device
> > *pdev)
> > master->max_speed_hz = min_t(unsigned int, rate >> 1,
> > spicc->data->max_speed_hz);
> >
> > + ret = meson_spicc_clk_init(spicc);
> > + if (ret) {
> > + dev_err(&pdev->dev, "clock registration failed\n");
> > + goto out_master;
> > + }
> > +
> > ret = devm_spi_register_master(&pdev->dev, master);
> > if (ret) {
> > dev_err(&pdev->dev, "spi master registration failed\n");
> > @@ -639,6 +767,7 @@ static const struct meson_spicc_data
> > meson_spicc_gx_data = {
> > static const struct meson_spicc_data meson_spicc_axg_data = {
> > .max_speed_hz = 80000000,
> > .has_oen = true,
> > + .has_enhance_clk_div = true,
> > };
> >
> > static const struct of_device_id meson_spicc_of_match[] = {
> >


\
 
 \ /
  Last update: 2018-12-13 10:29    [W:0.078 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site