lkml.org 
[lkml]   [2018]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/3] spi: meson-axg: support MAX 80M clock
From
Date
Hi Sunny,

On 13/12/2018 09:39, Sunny Luo wrote:
> The SPICC controller in Meson-AXG is capable of running at 80M clock.
> The ASIC IP is improved and the clock is actually running higher than
> previous old SoCs.
>
> Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> ---
> drivers/spi/spi-meson-spicc.c | 37 +++++++++++++++++++++++++++++--------
> 1 file changed, 29 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
> index 7fe4488..b56249d 100644
> --- a/drivers/spi/spi-meson-spicc.c
> +++ b/drivers/spi/spi-meson-spicc.c
> @@ -9,11 +9,13 @@
>
> #include <linux/bitfield.h>
> #include <linux/clk.h>
> +#include <linux/clk-provider.h>
> #include <linux/device.h>
> #include <linux/io.h>
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/of.h>
> +#include <linux/of_device.h>
> #include <linux/platform_device.h>
> #include <linux/spi/spi.h>
> #include <linux/types.h>
> @@ -34,7 +36,6 @@
> * to have a CS go down over the full transfer
> */
>
> -#define SPICC_MAX_FREQ 30000000
> #define SPICC_MAX_BURST 128
>
> /* Register Map */
> @@ -120,6 +121,10 @@
> #define SPICC_BURST_MAX 16
> #define SPICC_FIFO_HALF 10
>
> +struct meson_spicc_data {
> + unsigned int max_speed_hz;
> +};
> +
> struct meson_spicc_device {
> struct spi_master *master;
> struct platform_device *pdev;
> @@ -127,6 +132,7 @@ struct meson_spicc_device {
> struct clk *core;
> struct spi_message *message;
> struct spi_transfer *xfer;
> + const struct meson_spicc_data *data;
> u8 *tx_buf;
> u8 *rx_buf;
> unsigned int bytes_per_word;
> @@ -517,6 +523,9 @@ static int meson_spicc_probe(struct platform_device *pdev)
> spicc->pdev = pdev;
> platform_set_drvdata(pdev, spicc);
>
> + spicc->data = (const struct meson_spicc_data *)
> + of_device_get_match_data(&pdev->dev);
> +
> res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> spicc->base = devm_ioremap_resource(&pdev->dev, res);
> if (IS_ERR(spicc->base)) {
> @@ -567,11 +576,9 @@ static int meson_spicc_probe(struct platform_device *pdev)
> master->unprepare_transfer_hardware = meson_spicc_unprepare_transfer;
> master->transfer_one = meson_spicc_transfer_one;
>
> - /* Setup max rate according to the Meson GX datasheet */
> - if ((rate >> 2) > SPICC_MAX_FREQ)
> - master->max_speed_hz = SPICC_MAX_FREQ;
> - else
> - master->max_speed_hz = rate >> 2;
> + /* Setup max rate according to the Meson datasheet */
> + master->max_speed_hz = min_t(unsigned int, rate >> 1,
> + spicc->data->max_speed_hz);

I think "rate >> 1" here depends on patch 3, either move patch 3 before this one
or keep "rate >> 2" and change it back to "rate >> 1" on patch 3.

>
> ret = devm_spi_register_master(&pdev->dev, master);
> if (ret) {
> @@ -602,9 +609,23 @@ static int meson_spicc_remove(struct platform_device *pdev)
> return 0;
> }
>
> +static const struct meson_spicc_data meson_spicc_gx_data = {
> + .max_speed_hz = 30000000,
> +};
> +
> +static const struct meson_spicc_data meson_spicc_axg_data = {
> + .max_speed_hz = 80000000,
> +};
> +
> static const struct of_device_id meson_spicc_of_match[] = {
> - { .compatible = "amlogic,meson-gx-spicc", },
> - { .compatible = "amlogic,meson-axg-spicc", },
> + {
> + .compatible = "amlogic,meson-gx-spicc",
> + .data = &meson_spicc_gx_data,
> + },
> + {
> + .compatible = "amlogic,meson-axg-spicc",
> + .data = &meson_spicc_axg_data,
> + },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, meson_spicc_of_match);
>

\
 
 \ /
  Last update: 2018-12-13 09:50    [W:0.134 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site