lkml.org 
[lkml]   [2018]   [Dec]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
From
Date
Hi,

On 10/12/18 8:55 PM, Ulf Hansson wrote:
> On Mon, 10 Dec 2018 at 15:04, Faiz Abbas <faiz_abbas@ti.com> wrote:
>>
>> Hi,
>>
>> On 10/12/18 7:15 PM, Ulf Hansson wrote:
>>> On Mon, 10 Dec 2018 at 14:23, Faiz Abbas <faiz_abbas@ti.com> wrote:
>>>>
>>>> Hi Uffe,
>>>>
>>>> On 05/12/18 7:20 PM, Ulf Hansson wrote:
>>>>> On Fri, 30 Nov 2018 at 06:53, Faiz Abbas <faiz_abbas@ti.com> wrote:
>>>>>>
>>>>>> Hi Kishon,
>>>>>>
>>>>>> On 30/11/18 10:10 AM, Kishon Vijay Abraham I wrote:
>>>>>>> Hi Faiz,
>>>>>>>
>>>>>>> On 30/11/18 12:35 AM, Faiz Abbas wrote:
>>>>>>>> Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
>>>>>>>> (SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
>>>>>>>> unexpected tuning pattern errors. A small failure band may be present
>>>>>>>> in the tuning range which may be missed by the current algorithm.
>>>>>>>> Furthermore, the failure bands vary with temperature leading to
>>>>>>>> different optimum tuning values for different temperatures.
>>>>>>>>
>>>>>>>> As suggested in the related Application Report (SPRACA9B - October 2017
>>>>>>>> - Revised July 2018 [2]), tuning should be done in two stages.
>>>>>>>> In stage 1, assign the optimum ratio in the maximum pass window for the
>>>>>>>> current temperature. In stage 2, if the chosen value is close to the
>>>>>>>> small failure band, move away from it in the appropriate direction.
>>>>>>>>
>>>>>>>> References:
>>>>>>>> [1] http://www.ti.com/lit/pdf/sprz426
>>>>>>>> [2] http://www.ti.com/lit/pdf/SPRACA9
>>>>>>>>
>>>>>>>> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
>>>>>>>> ---
>> ...
>>>>>>>
>>>>>>> Can't we get thermal zone once during probe?
>>>>>>>
>>>>>>
>>>>>> Tuning is also (ideally) supposed to happen only once per enumeration.
>>>>>> Also it doesn't make sense to get a thermal zone for lower speed systems
>>>>>> that won't do tuning.
>>>>>
>>>>> Currently sdhci-omap calls pm_runtime_get_sync() during probe, and
>>>>> then keeps the host device runtime resumed until ->remove() is called
>>>>> on it. I assume you are going to change that, at some point!?
>>>>>
>>>>> In other words, what will happen to the host device when it becomes
>>>>> runtime suspended? Is re-tuning needed when it gets runtime resumed,
>>>>> which is the case for many other sdhci variants?
>>>>
>>>> There are no plans to support runtime_suspend()/resume() any time in the
>>>> near future. If its ok with you, I would like to get this patch in
>>>> without any changes. We can change it in case a need for
>>>> runtime_suspend()/_resume() does arise.
>>>
>>> Right, I am okay with that. Due to recent changes to sdhci-omap
>>> $subject patch doesn't apply, can you please rebase!?
>>>
>>> Additionally, I realized that we should fold in patch updating the DT
>>> doc for sdhci-omap, adding the property for the thermal zone. I
>>> regards to that, I am wondering if "cpu_thermal", is really the
>>> correct name of the zone. The point is, I am guessing the zone could
>>> change along with the SoCs/platforms.
>>>
>>
>> As you have probably noticed, we are introducing a new driver
>> (sdhci_am654) for newer platforms. I don't foresee using sdhci-omap
>> driver with any other platforms. In case we do use it, we can add the dt
>> property at that point of time and default to "cpu_thermal" to maintain
>> dt compatibility.
>>
>> Will rebase and send v2 if you are ok with above.
>
> I see, but you still need to update the DT doc for sdhci-omap.
>

I didn't get you. There are no changes in dt. What changes should I
document?

Thanks,
Faiz

\
 
 \ /
  Last update: 2018-12-10 17:43    [W:0.385 / U:0.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site