lkml.org 
[lkml]   [2018]   [Dec]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH v3 2/2] pwm: imx: Configure output to GPIO in disabled state
On Mon, Dec 10, 2018 at 11:15:05AM +0000, Vokáč Michal wrote:
> On 6.12.2018 17:16, Uwe Kleine-König wrote:
> > On Thu, Dec 06, 2018 at 03:37:55PM +0000, Vokáč Michal wrote:
> >> On 6.12.2018 14:59, Uwe Kleine-König wrote:
> >>> On Thu, Dec 06, 2018 at 01:41:31PM +0000, Vokáč Michal wrote:
> >>>
> >>> Can it happen, that pinctrl_pins_pwm is PTR_ERR(-EPROBE_DEFER)?
> >>
> >> No. The pinctrl_lookup_state either returns pointer to the pinctrl state
> >> or ERR_PTR(-ENODEV). But I do not explicitly test the pinctrl_pins_pwm
> >> for PTR_ERR(-EPROBE_DEFER), or do I?
> >
> > You don't, I just wondered if this could happen and the function should
> > return -EPROBE_DEFER in this case, too.
>
> OK.
>
> >>> Maybe you only want to ignore PTR_ERR(-ENODEV) and for example propagate
> >>> -EIO? I think you want to put the gpio if the failure is because there
> >>> is a pinctrl related error.
> >>
> >> I think that is what I am doing. In case the GPIO is not ready the probe
> >> is deferred. In case of any other error with the GPIO or pinctrl failure
> >> I put the pinctrl. Or maybe I do not really understand what you mean.
> >
> > Yes, you put the pinctrl, but not the GPIO. I.e. you're not undoing
> > devm_gpiod_get_optional(). Maybe only do this if the pinctrl stuff
> > succeeded to not touch the GPIO if it won't be used?
>
> OK, I agree it seems better to get the pinctrl first and if it succeeds
> only then try to get the GPIO. In that case I need to use the non-optional
> variant of devm_gpio_get(). Note that then I do not really need to put the
> GPIO in the error path as it means I did not get it.
> The code would look like:
>
> +static int imx_pwm_init_pinctrl_info(struct imx_chip *imx_chip,
> + struct platform_device *pdev)
> +{
> + imx_chip->pinctrl = devm_pinctrl_get(&pdev->dev);
> + if (IS_ERR(imx_chip->pinctrl)) {
> + dev_dbg(&pdev->dev, "can not get pinctrl\n");
> + return PTR_ERR(imx_chip->pinctrl);
> + }
> +
> + imx_chip->pinctrl_pins_pwm = pinctrl_lookup_state(imx_chip->pinctrl,
> + "pwm");
> + imx_chip->pinctrl_pins_gpio = pinctrl_lookup_state(imx_chip->pinctrl,
> + "gpio");
> +
> + if (IS_ERR(imx_chip->pinctrl_pins_pwm) ||
> + IS_ERR(imx_chip->pinctrl_pins_gpio)) {
> + dev_dbg(&pdev->dev, "pinctrl information incomplete\n");
> + goto out;
> + }
> +
> + imx_chip->pwm_gpiod = devm_gpiod_get(&pdev->dev, "pwm", GPIOD_IN);
> + if (PTR_ERR(imx_chip->pwm_gpiod) == -EPROBE_DEFER) {
> + return -EPROBE_DEFER;
> + } else if (IS_ERR(imx_chip->pwm_gpiod)) {
> + dev_dbg(&pdev->dev, "GPIO information incomplete\n");
> + goto out;
> + }
> +
> + return 0;
> +
> +out:
> + devm_pinctrl_put(imx_chip->pinctrl);
> + imx_chip->pinctrl = NULL;
> +
> + return 0;
> +}

This looks right.

> >>> ISTR that there was a patch that implements get_state for imx. Is there
> >>> a dependency on that one? Otherwise the state returned by
> >>> pwm_get_state() might not be what is actually configured.
> >>
> >> No, it should be independent. One can go without the other. I tested all
> >> three combinations (mainline with .get_state, mainline with this series,
> >> mainline with .get_state AND this series) and got the expected results.
> >> Without the .get_state() patch the core always returns the default which
> >> is disabled state so the gpio pinctrl state is selected in probe.
> >
> > Without .get_state it won't be possible to smoothly take over a running
> > PWM.
>
> But that is exactly how the current pwm-imx code works, right?

But then at least the pwm would run until the first consumer
reconfigures it.

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |

\
 
 \ /
  Last update: 2018-12-10 12:18    [W:0.104 / U:0.916 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site