lkml.org 
[lkml]   [2018]   [Nov]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 0/9] dt-bindings: Firmware node binding for ZynqMP core
Date
Ping for comments

> -----Original Message-----
> From: Jolly Shah [mailto:jolly.shah@xilinx.com]
> Sent: Friday, November 16, 2018 3:57 PM
> To: robh+dt@kernel.org; mark.rutland@arm.com
> Cc: Michal Simek <michals@xilinx.com>; Rajan Vaja <RAJANV@xilinx.com>;
> Nava kishore Manne <navam@xilinx.com>; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> devicetree@vger.kernel.org; Jolly Shah <JOLLYS@xilinx.com>
> Subject: [PATCH 0/9] dt-bindings: Firmware node binding for ZynqMP core
>
> Base firmware node and clock child node binding are part of mainline kernel.
> This patchset adds documentation to describe rest of the firmware child node
> bindings.
> Complete firmware DT node example is shown below for ease of understanding:
>
> firmware {
> zynqmp_firmware: zynqmp-firmware {
> compatible = "xlnx,zynqmp-firmware";
> method = "smc";
> #power-domain-cells = <1>;
> #reset-cells = <1>;
>
> zynqmp_clk: clock-controller {
> #clock-cells = <1>;
> compatible = "xlnx,zynqmp-clk";
> clocks = <&pss_ref_clk>, <&video_clk>,
> <&pss_alt_ref_clk>, <&aux_ref_clk>, <&gt_crx_ref_clk>;
> clock-names = "pss_ref_clk", "video_clk",
> "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk";
> };
>
> zynqmp_power: zynqmp-power {
> compatible = "xlnx,zynqmp-power";
> interrupts = <0 35 4>;
> };
>
> nvmem_firmware {
> compatible = "xlnx,zynqmp-nvmem-fw";
> #address-cells = <1>;
> #size-cells = <1>;
>
> /* Data cells */
> soc_revision: soc_revision {
> reg = <0x0 0x4>;
> };
> };
>
> afi0: afi0 {
> compatible = "xlnx,afi-fpga";
> config-afi = <0 2>, <1 1>, <2 1>;
> };
>
> qspi: spi@ff0f0000 {
> compatible = "xlnx,zynqmp-qspi-1.0";
> clock-names = "ref_clk", "pclk";
> clocks = <&misc_clk &misc_clk>;
> interrupts = <0 15 4>;
> interrupt-parent = <&gic>;
> num-cs = <1>;
> reg = <0x0 0xff0f0000 0x1000>,<0x0 0xc0000000
> 0x8000000>;
> };
>
> serdes: zynqmp_phy@fd400000 {
> compatible = "xlnx,zynqmp-psgtr";
> status = "okay";
> reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000
> 0x0 0x1000>,
> <0x0 0xff5e0000 0x0 0x1000>;
> reg-names = "serdes", "siou", "lpd";
>
> lane0: lane@0 {
> #phy-cells = <4>;
> };
> lane1: lane@1 {
> #phy-cells = <4>;
> };
> lane2: lane@2 {
> #phy-cells = <4>;
> };
> lane3: lane@3 {
> #phy-cells = <4>;
> };
> };
>
> pinctrl_uart1_default: uart1-default {
> mux {
> groups = "uart0_4_grp";
> function = "uart0";
> };
>
> conf {
> groups = "uart0_4_grp";
> slew-rate = <SLEW_RATE_SLOW>;
> io-standard = <IO_STANDARD_LVCMOS18>;
> };
>
> conf-rx {
> pins = "MIO18";
> bias-high-impedance;
> };
>
> conf-tx {
> pins = "MIO19";
> bias-disable;
> schmitt-cmos = <PIN_INPUT_TYPE_CMOS>;
> };
> };
> zynqmp-r5-remoteproc@0 {
> compatible = "xlnx,zynqmp-r5-remoteproc-1.0";
> reg = <0x0 0xFFE00000 0x0 0x10000>,
> <0x0 0xFFE20000 0x0 0x10000>,
> <0x0 0xff340000 0x0 0x100>;
> reg-names = "tcm_a", "tcm_b", "ipi";
> dma-ranges;
> core_conf = "split0";
> memory-region = <&rproc_0_fw_reserved>,
> <&rproc_0_dma_reserved>;
> tcm-pnode-id = <0xf>, <0x10>;
> rpu-pnode-id = <0x7>;
> interrupt-parent = <&gic>;
> interrupts = <0 29 4>;
> };
> };
> };
>
> Jolly Shah (2):
> dt-bindings: phy: Add dt bindings for ZynqMP PHY
> dt-bindings: fpga: Add binding doc for the afi config driver
>
> Nava kishore Manne (2):
> dt-bindings: reset: Add bindings for ZynqMP reset driver
> dt-bindings: nvmem: Add bindings for ZynqMP nvmem driver
>
> Rajan Vaja (4):
> dt-bindings: power: Add ZynqMP power domain bindings
> dt-bindings: soc: Add ZynqMP PM bindings
> dt-bindings: pinctrl: Add ZynqMP pin controller bindings
> dt-bindings: spi: zynqmp: Move SPI node under zynqmp firmware
>
> Wendy Liang (1):
> dt-bindings: remoteproc: Add Xilinx R5 rproc binding
>
> .../devicetree/bindings/fpga/xlnx,afi-fpga.txt | 67 +++++
> .../bindings/nvmem/xlnx,zynqmp-nvmem.txt | 44 ++++
> .../devicetree/bindings/phy/phy-zynqmp.txt | 126 ++++++++++
> .../bindings/pinctrl/xlnx,zynqmp-pinctrl.txt | 272 +++++++++++++++++++++
> .../bindings/power/reset/xlnx,zynqmp-power.txt | 25 ++
> .../bindings/power/xlnx,zynqmp-genpd.txt | 34 +++
> .../remoteproc/xlnx,zynqmp-r5-remoteproc.txt | 81 ++++++
> .../bindings/reset/xlnx,zynqmp-reset.txt | 148 +++++++++++
> .../devicetree/bindings/spi/spi-zynqmp-qspi.txt | 22 +-
> include/dt-bindings/power/xlnx-zynqmp-power.h | 39 +++
> 10 files changed, 850 insertions(+), 8 deletions(-) create mode 100644
> Documentation/devicetree/bindings/fpga/xlnx,afi-fpga.txt
> create mode 100644 Documentation/devicetree/bindings/nvmem/xlnx,zynqmp-
> nvmem.txt
> create mode 100644 Documentation/devicetree/bindings/phy/phy-zynqmp.txt
> create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-
> pinctrl.txt
> create mode 100644
> Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
> create mode 100644 Documentation/devicetree/bindings/power/xlnx,zynqmp-
> genpd.txt
> create mode 100644
> Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5-
> remoteproc.txt
> create mode 100644 Documentation/devicetree/bindings/reset/xlnx,zynqmp-
> reset.txt
> create mode 100644 include/dt-bindings/power/xlnx-zynqmp-power.h
>
> --
> 2.7.4

\
 
 \ /
  Last update: 2018-11-26 22:40    [W:0.151 / U:0.132 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site