lkml.org 
[lkml]   [2018]   [Nov]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 3/8] dt-bindings: regulator: document stpmic1 pmic regulators
Date
The STPMIC1 regulators supply power to the application processor as well as
to the external system peripherals such as DDR, Flash memories and system
devices.

Signed-off-by: Pascal Paillet <p.paillet@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
changes in v6:
* remove interrupt parent

.../bindings/regulator/st,stpmic1-regulator.txt | 67 ++++++++++++++++++++++
1 file changed, 67 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt

diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt
new file mode 100644
index 0000000..5adc938
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt
@@ -0,0 +1,66 @@
+STMicroelectronics STPMIC1 Voltage regulators
+
+Regulator Nodes are optional depending on needs.
+
+Available Regulators in STPMIC1 device are:
+ - buck1 for Buck BUCK1
+ - buck2 for Buck BUCK2
+ - buck3 for Buck BUCK3
+ - buck4 for Buck BUCK4
+ - ldo1 for LDO LDO1
+ - ldo2 for LDO LDO2
+ - ldo3 for LDO LDO3
+ - ldo4 for LDO LDO4
+ - ldo5 for LDO LDO5
+ - ldo6 for LDO LDO6
+ - vref_ddr for LDO Vref DDR
+ - boost for Buck BOOST
+ - pwr_sw1 for VBUS_OTG switch
+ - pwr_sw2 for SW_OUT switch
+
+Switches are fixed voltage regulators with only enable/disable capability.
+
+Optional properties:
+- st,mask-reset: mask reset for this regulator: the regulator configuration
+ is maintained during pmic reset.
+- regulator-pull-down: enable high pull down
+ if not specified light pull down is used
+- regulator-over-current-protection:
+ if set, all regulators are switched off in case of over-current detection
+ on this regulator,
+ if not set, the driver only sends an over-current event.
+- interrupts: index of current limit detection interrupt
+- <regulator>-supply: phandle to the parent supply/regulator node
+ each regulator supply can be described except vref_ddr.
+- regulator-active-discharge: can be used on pwr_sw1 and pwr_sw2.
+
+Example:
+regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo6-supply = <&v3v3>;
+
+ vdd_core: buck1 {
+ regulator-name = "vdd_core";
+ interrupts = <IT_CURLIM_BUCK1 0>;
+ st,mask-reset;
+ regulator-pull-down;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ interrupts = <IT_CURLIM_BUCK4 0>;
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ v1v8: ldo6 {
+ regulator-name = "v1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-over-current-protection;
+ };
+};
--
1.9.1
\
 
 \ /
  Last update: 2018-11-27 17:53    [W:0.070 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site