lkml.org 
[lkml]   [2018]   [Nov]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: NO_BOOTMEM breaks alpha pc164
From
Date
> Two things that might cause the hang.
> First, memblock_add() is called after node_min_pfn has been rounded down to
> the nearest 8Mb and in your case this cases memblock to see more memory that
> is actually present in the system.
> I'm not sure why the 8Mb alignment is required, I've just made sure that
> memblock_add() will use exact available memory (the first patch below).
>
> Another thing is that memblock allocates memory from high addresses while
> bootmem was using low memory. It may happen that an allocation from high
> memory is not accessible by the hardware, although it should be. The second
> patch below addresses this issue.
>
> It would be really great if you could test with each patch separately and
> with both patches applied :)

Tested separateöy and together, with the previous debug patch applied.

debug+patch1 caused no visible change cmpared to just debug - same crash before starting init as with plain debug patch.

debug+patch2 caused a change - now instead of hang before starting init, it hangs after starting init as with no patch applied.

debug+patch1+patch2: works, dmesg attached:

[ 0.000000] Linux version 4.20.0-rc2-00068-gda5322e65940-dirty (mroos@pc164) (gcc version 7.3.0 (Gentoo 7.3.0-r3 p1.4)) #118 Mon Nov 26 12:24:51 EET 2018
[ 0.000000] Booting on EB164 variation PC164 using machine vector PC164 from SRM
[ 0.000000] Major Options: EV56 LEGACY_START VERBOSE_MCHECK DISCONTIGMEM MAGIC_SYSRQ
[ 0.000000] Command line: root=/dev/sda2 console=ttyS0
[ 0.000000] Raw memory layout:
[ 0.000000] memcluster 0, usage 1, start 0, end 192
[ 0.000000] memcluster 1, usage 0, start 192, end 32651
[ 0.000000] memcluster 2, usage 1, start 32651, end 32768
[ 0.000000] Initializing bootmem allocator on Node ID 0
[ 0.000000] memcluster 1, usage 0, start 192, end 32651
[ 0.000000] Detected node memory: start 192, end 32651
[ 0.000000] memblock_add: [0x0000000000180000-0x000000000ff15fff] setup_memory+0x38c/0x470
[ 0.000000] memblock_reserve: [0x0000000000300000-0x0000000000c11fff] setup_memory+0x43c/0x470
[ 0.000000] 1024K Bcache detected; load hit latency 30 cycles, load miss latency 212 cycles
[ 0.000000] pci: cia revision 2
[ 0.000000] memblock_alloc_try_nid: 104 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 alloc_pci_controller+0x2c/0x50
[ 0.000000] memblock_reserve: [0x0000000000c12000-0x0000000000c12067] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 64 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 alloc_resource+0x2c/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12080-0x0000000000c120bf] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 40 bytes align=0x8000 nid=0 from=0x0000000000000000 max_addr=0x0000000000000000 iommu_arena_new_node+0x74/0x1b0
[ 0.000000] memblock_reserve: [0x0000000000c18000-0x0000000000c18027] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 40 bytes align=0x8000 nid=0 from=0x0000000000000000 max_addr=0x0000000000000000 iommu_arena_new_node+0x104/0x1b0
[ 0.000000] memblock_reserve: [0x0000000000c20000-0x0000000000c20027] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 1024 bytes align=0x8000 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 do_init_arch+0x37c/0x448
[ 0.000000] memblock_reserve: [0x0000000000c28000-0x0000000000c283ff] memblock_alloc_internal+0x170/0x278
[ 0.000000] On node 0 totalpages: 32651
[ 0.000000] memblock_alloc_try_nid_nopanic: 1835008 bytes align=0x20 nid=0 from=0x0000000000000000 max_addr=0x0000000000000000 alloc_node_mem_map+0x7c/0xa8
[ 0.000000] memblock_reserve: [0x0000000000c28400-0x0000000000de83ff] memblock_alloc_internal+0x170/0x278
[ 0.000000] DMA zone: 224 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 32651 pages, LIFO batch:7
[ 0.000000] memblock_alloc_try_nid_nopanic: 16 bytes align=0x20 nid=0 from=0x0000000000000000 max_addr=0x0000000000000000 setup_usemap.isra.111+0x5c/0x78
[ 0.000000] memblock_reserve: [0x0000000000c120c0-0x0000000000c120cf] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 29 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.14+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c120e0-0x0000000000c120fc] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 29 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.14+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12100-0x0000000000c1211c] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 29 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.14+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12120-0x0000000000c1213c] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid_nopanic: 8192 bytes align=0x2000 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 pcpu_alloc_alloc_info+0x5c/0xc8
[ 0.000000] memblock_reserve: [0x0000000000c14000-0x0000000000c15fff] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid_nopanic: 32768 bytes align=0x2000 nid=-1 from=0x000003ffffffffff max_addr=0x0000000000000000 setup_per_cpu_areas+0x70/0x118
[ 0.000000] memblock_reserve: [0x0000000000dea000-0x0000000000df1fff] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 8 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12140-0x0000000000c12147] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 8 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12160-0x0000000000c12167] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 4 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12180-0x0000000000c12183] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 8 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c121a0-0x0000000000c121a7] memblock_alloc_internal+0x170/0x278
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] memblock_alloc_try_nid: 240 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c121c0-0x0000000000c122af] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 105 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c122c0-0x0000000000c12328] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 1024 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12340-0x0000000000c1273f] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 1032 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12740-0x0000000000c12b47] memblock_alloc_internal+0x170/0x278
[ 0.000000] memblock_alloc_try_nid: 80 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 memblock_alloc.constprop.29+0x28/0x40
[ 0.000000] memblock_reserve: [0x0000000000c12b60-0x0000000000c12baf] memblock_alloc_internal+0x170/0x278
[ 0.000000] __memblock_free_early: [0x0000000000c14000-0x0000000000c15fff] pcpu_free_alloc_info+0x2c/0x40
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32427
[ 0.000000] Kernel command line: root=/dev/sda2 console=ttyS0
[ 0.000000] memblock_alloc_try_nid_nopanic: 262144 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 alloc_large_system_hash+0x258/0x3dc
[ 0.000000] memblock_reserve: [0x0000000000df2000-0x0000000000e31fff] memblock_alloc_internal+0x170/0x278
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 262144 bytes)
[ 0.000000] memblock_alloc_try_nid_nopanic: 131072 bytes align=0x20 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 alloc_large_system_hash+0x258/0x3dc
[ 0.000000] memblock_reserve: [0x0000000000e32000-0x0000000000e51fff] memblock_alloc_internal+0x170/0x278
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 131072 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 248144K/261208K available (5455K kernel code, 372K rwdata, 1740K rodata, 200K init, 1425K bss, 13064K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=128
[ 0.000000] NR_IRQS: 35
[ 0.000000] clocksource: rpcc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 3822520893 ns
[ 0.001953] Console: colour VGA+ 80x25
[ 0.073242] printk: console [ttyS0] enabled
[ 0.074218] Calibrating delay loop... 985.92 BogoMIPS (lpj=480768)
[ 0.083007] pid_max: default: 32768 minimum: 301
[ 0.084960] Mount-cache hash table entries: 1024 (order: 0, 8192 bytes)
[ 0.085937] Mountpoint-cache hash table entries: 1024 (order: 0, 8192 bytes)
[ 0.096679] devtmpfs: initialized
[ 0.098632] random: get_random_u32 called from bucket_table_alloc.isra.19+0xbc/0x280 with crng_init=0
[ 0.101562] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1866466235866741 ns
[ 0.102539] futex hash table entries: 256 (order: -1, 6144 bytes)
[ 0.104492] NET: Registered protocol family 16
[ 0.106445] pci: passed tb register update test
[ 0.108398] pci: passed sg loopback i/o read test
[ 0.109374] pci: passed tbia test
[ 0.110351] pci: passed pte write cache snoop test
[ 0.111328] pci: failed valid tag invalid pte reload test (mcheck; workaround available)
[ 0.112304] pci: passed pci machine check test
[ 0.113281] PCI host bridge to bus 0000:00
[ 0.114257] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.115234] pci_bus 0000:00: root bus resource [mem 0x00000000-0x1fffffff]
[ 0.116210] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.117187] pci 0000:00:05.0: [1000:000f] type 00 class 0x010000
[ 0.117187] pci 0000:00:05.0: reg 0x10: [io 0x10000-0x100ff]
[ 0.117187] pci 0000:00:05.0: reg 0x14: [mem 0x82875000-0x828750ff]
[ 0.117187] pci 0000:00:05.0: reg 0x18: [mem 0x82874000-0x82874fff]
[ 0.118164] pci 0000:00:05.0: reg 0x30: [mem 0x82840000-0x8285ffff pref]
[ 0.118164] pci 0000:00:06.0: [102b:051b] type 00 class 0x030000
[ 0.118164] pci 0000:00:06.0: reg 0x10: [mem 0x88000000-0x88ffffff pref]
[ 0.118164] pci 0000:00:06.0: reg 0x14: [mem 0x82870000-0x82873fff]
[ 0.118164] pci 0000:00:06.0: reg 0x18: [mem 0x82000000-0x827fffff]
[ 0.118164] pci 0000:00:06.0: reg 0x30: [mem 0x82860000-0x8286ffff pref]
[ 0.119140] pci 0000:00:08.0: [8086:0484] type 00 class 0x000000
[ 0.119140] pci 0000:00:09.0: [1011:0009] type 00 class 0x020000
[ 0.119140] pci 0000:00:09.0: reg 0x10: [io 0x10100-0x1017f]
[ 0.119140] pci 0000:00:09.0: reg 0x14: [mem 0x82875100-0x8287517f]
[ 0.119140] pci 0000:00:09.0: reg 0x30: [mem 0x82800000-0x8283ffff pref]
[ 0.120117] pci 0000:00:0b.0: [1095:0646] type 00 class 0x010180
[ 0.120117] pci 0000:00:0b.0: reg 0x20: [io 0x10180-0x1018f]
[ 0.120117] pci 0000:00:0b.0: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.121093] pci 0000:00:0b.0: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.122070] pci 0000:00:0b.0: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.123046] pci 0000:00:0b.0: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.124023] pci: enabling save/restore of SRM state
[ 0.124999] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.124999] pci 0000:00:06.0: BAR 0: assigned [mem 0x03000000-0x03ffffff pref]
[ 0.125976] pci 0000:00:06.0: BAR 2: assigned [mem 0x02800000-0x02ffffff]
[ 0.126953] pci 0000:00:09.0: BAR 6: assigned [mem 0x02200000-0x0223ffff pref]
[ 0.127929] pci 0000:00:05.0: BAR 6: assigned [mem 0x02240000-0x0225ffff pref]
[ 0.128906] pci 0000:00:06.0: BAR 6: assigned [mem 0x02260000-0x0226ffff pref]
[ 0.130859] pci 0000:00:06.0: BAR 1: assigned [mem 0x02270000-0x02273fff]
[ 0.131835] pci 0000:00:05.0: BAR 2: assigned [mem 0x02274000-0x02274fff]
[ 0.132812] pci 0000:00:05.0: BAR 0: assigned [io 0x8000-0x80ff]
[ 0.133788] pci 0000:00:05.0: BAR 1: assigned [mem 0x02275000-0x022750ff]
[ 0.134765] pci 0000:00:09.0: BAR 0: assigned [io 0x8400-0x847f]
[ 0.135742] pci 0000:00:09.0: BAR 1: assigned [mem 0x02276000-0x0227607f]
[ 0.136718] pci 0000:00:0b.0: BAR 4: assigned [io 0x8480-0x848f]
[ 0.137695] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.137695] pci_bus 0000:00: resource 5 [mem 0x00000000-0x1fffffff]
[ 0.138671] SMC FDC37C93X Ultra I/O Controller found @ 0x370
[ 0.149413] pci 0000:00:06.0: vgaarb: setting as boot VGA device
[ 0.149413] pci 0000:00:06.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.150390] pci 0000:00:06.0: vgaarb: bridge control possible
[ 0.151367] vgaarb: loaded
[ 0.153320] SCSI subsystem initialized
[ 0.157226] clocksource: Switched to clocksource rpcc
[ 0.182617] NET: Registered protocol family 2
[ 0.185546] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 8192 bytes)
[ 0.186523] TCP established hash table entries: 2048 (order: 1, 16384 bytes)
[ 0.187499] TCP bind hash table entries: 2048 (order: 1, 16384 bytes)
[ 0.188476] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.190429] UDP hash table entries: 256 (order: 0, 8192 bytes)
[ 0.191406] UDP-Lite hash table entries: 256 (order: 0, 8192 bytes)
[ 0.193359] NET: Registered protocol family 1
[ 0.194335] PCI: CLS 0 bytes, default 32
[ 0.196288] srm_env: version 0.0.6 loaded successfully
[ 0.197265] Using epoch 2000 for rtc year 18
[ 0.200195] platform rtc-alpha: rtc core: registered rtc-alpha as rtc0
[ 0.203124] workingset: timestamp_bits=55 max_order=15 bucket_order=0
[ 0.241210] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.242187] io scheduler noop registered
[ 0.244140] io scheduler cfq registered (default)
[ 0.247070] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.249023] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.249999] random: fast init done
[ 0.252929] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 0.406249] sym0: <875> rev 0x3 at pci 0000:00:05.0 irq 18
[ 0.410156] Floppy drive(s): fd0 is 2.88M
[ 0.499999] sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
[ 0.500976] sym0: open drain IRQ line driver, using on-chip SRAM
[ 0.501952] sym0: using LOAD/STORE-based firmware.
[ 0.502929] sym0: SCSI BUS has been reset.
[ 0.503905] scsi host0: sym-2.2.3
[ 0.506835] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
[ 0.511718] tulip0: Old format EEPROM on 'Accton EN1207' board. Using substitute media control info
[ 0.512695] tulip0: EEPROM default media type Autosense
[ 0.513671] tulip0: Index #0 - Media 10base2 (#1) described by a 21140 non-MII (0) block
[ 0.514648] tulip0: Index #1 - Media 10baseT (#0) described by a 21140 non-MII (0) block
[ 0.516601] tulip0: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block
[ 0.517577] tulip0: Index #3 - Media 100baseTx (#3) described by a 21140 non-MII (0) block
[ 0.518554] tulip0: Index #4 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block
[ 0.520507] net eth0: Digital DS21140 Tulip rev 34 at MMIO 0x2276000, 00:00:e8:3c:4e:c2, IRQ 19
[ 0.527343] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.528320] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.532226] NET: Registered protocol family 10
[ 0.536132] FDC 0 is a post-1991 82077
[ 0.546874] Segment Routing with IPv6
[ 0.547851] NET: Registered protocol family 17
[ 0.549804] atkbd serio0: keyboard reset failed on isa0060/serio0
[ 0.553710] platform rtc-alpha: setting system clock to 2018-11-26 10:35:27 UTC (1543228527)
[ 0.609374] atkbd serio1: keyboard reset failed on isa0060/serio1
[ 0.685546] atkbd serio0: keyboard reset failed on isa0060/serio0
[ 0.750976] atkbd serio1: keyboard reset failed on isa0060/serio1
[ 3.902341] scsi 0:0:0:0: Direct-Access COMPAQ BF0369A4BC HPB7 PQ: 0 ANSI: 3
[ 3.903318] scsi target0:0:0: tagged command queuing enabled, command queue depth 16.
[ 3.904294] scsi target0:0:0: Beginning Domain Validation
[ 3.911130] scsi target0:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15)
[ 3.915037] scsi target0:0:0: Domain Validation skipping write tests
[ 3.916013] scsi target0:0:0: Ending Domain Validation
[ 3.917966] scsi 0:0:0:0: Power-on or device reset occurred
[ 8.038081] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8.039058] sd 0:0:0:0: [sda] 71132000 512-byte logical blocks: (36.4 GB/33.9 GiB)
[ 8.041011] sd 0:0:0:0: [sda] Write Protect is off
[ 8.041988] sd 0:0:0:0: [sda] Mode Sense: cf 00 10 08
[ 8.042964] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 8.058589] sda: sda1 sda2 sda4
[ 8.067378] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8.096675] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 8.098628] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 8.114253] devtmpfs: mounted
[ 8.116206] Freeing unused kernel memory: 200K
[ 8.118159] This architecture does not have kernel memory protection.
[ 8.119136] Run /sbin/init as init process
[ 8.398433] random: crng init done
[ 21.775379] udevd[477]: starting version 3.2.5
[ 21.947254] udevd[478]: starting eudev-3.2.5
[ 23.135730] tulip 0000:00:09.0 enp0s9: renamed from eth0
[ 23.919909] libata version 3.00 loaded.
[ 24.090807] scsi host1: pata_cmd64x
[ 24.114245] scsi host2: pata_cmd64x
[ 24.115222] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0x8480 irq 14
[ 24.115222] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0x8488 irq 15
[ 24.116198] pata_cmd64x: active 10 recovery 10 setup 3.
[ 24.116198] pata_cmd64x: active 10 recovery 10 setup 3.
[ 24.293932] ata1.00: ATAPI: SONY CD-RW CRX140E, 1.2a, max UDMA/33
[ 24.293932] pata_cmd64x: active 3 recovery 1 setup 1.
[ 24.293932] pata_cmd64x: active 3 recovery 1 setup 1.
[ 24.324206] scsi 1:0:0:0: CD-ROM SONY CD-RW CRX140E 1.2a PQ: 0 ANSI: 5
[ 24.341784] sr 1:0:0:0: [sr0] scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
[ 24.341784] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 24.346667] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 24.349596] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 24.351550] pata_cmd64x: active 10 recovery 10 setup 3.
[ 24.351550] pata_cmd64x: active 10 recovery 10 setup 3.
[ 29.886703] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 31.499983] Adding 1697208k swap on /dev/sda4. Priority:-2 extents:1 across:1697208k
[ 32.217756] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 32.240217] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)


--
Meelis Roos <mroos@linux.ee>

\
 
 \ /
  Last update: 2018-11-26 10:40    [W:0.162 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site