lkml.org 
[lkml]   [2018]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v7 1/4] dt-bindings: pps: descriptor-based gpio, capture-clear addition
Quoting Rob Herring <robh@kernel.org>:

> On Sat, Nov 17, 2018 at 4:35 AM tom burkart <tom@aussec.com> wrote:
>>
>> Quoting Rob Herring <robh@kernel.org>:
>>
>> > On Wed, Nov 14, 2018 at 11:54:29PM +1100, Tom Burkart wrote:
>> >> This patch changes the devicetree bindings for the pps-gpio driver
>> >> from the integer based ABI to the descriptor based ABI.
>> > ? That has nothing to do with DT.
>>
>> I believe it does, as the change in ABI forces a rename in the DT
>> naming convention.
>> This is due to the descriptor based ABI appending "-gpio" or "-gpios" (see
>> Documentation/gpio/base.txt.)
>> Admittedly, I may have called it by the wrong name due to ignorance,
>> my apologies.
>
> If what you say is correct, then you can't change this driver. You'll
> break compatibility with any existing DT.
>
> Changing the binding reasoning should purely be that this is the
> preferred form. Bindings must be independent from changing kernel
> APIs.

See comments from Philip Zabel. I misread the documentation and this
has now been corrected in v8 of the patch. I hope that eliminates all
comments made above.

>> >> It also adds
>> >> documentation for the device tree capture-clear option. The legacy
>> >> device tree entry for the GPIO pin is supported.
>> >>
>> >> Signed-off-by: Tom Burkart <tom@aussec.com>
>> >> ---
>> >> Documentation/devicetree/bindings/pps/pps-gpio.txt | 8 ++++++--
>> >> 1 file changed, 6 insertions(+), 2 deletions(-)
>> >>
>> >> diff --git a/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> b/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> index 3683874832ae..6c9fc0998d94 100644
>> >> --- a/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> +++ b/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> @@ -5,19 +5,23 @@ a GPIO pin.
>> >>
>> >> Required properties:
>> >> - compatible: should be "pps-gpio"
>> >> -- gpios: one PPS GPIO in the format described by ../gpio/gpio.txt
>> >> +- pps-gpios: one PPS GPIO in the format described by ../gpio/gpio.txt
>> >> +Alternatively (DEPRECATED), instead of pps-gpios above, it may have:
>> >> +- gpios: one PPS GPIO as above
>> >>
>> >> Optional properties:
>> >> - assert-falling-edge: when present, assert is indicated by a
>> falling edge
>> >> (instead of by a rising edge)
>> >> +- capture-clear: when present, also capture the PPS clear event
>> >
>> > Is this a h/w thing? or driver configuration?
>>
>> Driver configuration. Most of the code was present in the driver, yet
>> it was not documented, or usable due to a two line (code) omission
>> (the value was not being fetched from DT).
>
> So what determines how you want to configure this? If the user will
> want to change it, then it should be a sysfs attr and exposed to
> userspace. If it depends on h/w config for a board then it can be in
> DT.

Sorry, I misled you somewhat. If the PPS pulse active transition from
the hardware is on the falling edge, this flag is required to get the
OS to use that as the active transition. This would not change at the
user's whim but rather it is dependent on connected hardware.

Tom

\
 
 \ /
  Last update: 2018-11-18 01:36    [W:1.154 / U:0.688 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site