lkml.org 
[lkml]   [2018]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 6/7] net: phy: icplus: implement .did_interrupt for IP101A/G
Date
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.

This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default

Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
drivers/net/phy/icplus.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)

diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c
index c9489ec77cef..3dc8bbbe746b 100644
--- a/drivers/net/phy/icplus.c
+++ b/drivers/net/phy/icplus.c
@@ -44,6 +44,9 @@ MODULE_LICENSE("GPL");
#define IP101A_G_IRQ_CONF_STATUS 0x11 /* Conf Info IRQ & Status Reg */
#define IP101A_G_IRQ_PIN_USED BIT(15) /* INTR pin used */
#define IP101A_G_IRQ_ALL_MASK BIT(11) /* IRQ's inactive */
+#define IP101A_G_IRQ_SPEED_CHANGE BIT(2)
+#define IP101A_G_IRQ_DUPLEX_CHANGE BIT(1)
+#define IP101A_G_IRQ_LINK_CHANGE BIT(0)

static int ip175c_config_init(struct phy_device *phydev)
{
@@ -209,6 +212,18 @@ static int ip101a_g_config_intr(struct phy_device *phydev)
return phy_write(phydev, IP101A_G_IRQ_CONF_STATUS, val);
}

+static int ip101a_g_did_interrupt(struct phy_device *phydev)
+{
+ int val = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS);
+
+ if (val < 0)
+ return 0;
+
+ return val & (IP101A_G_IRQ_SPEED_CHANGE |
+ IP101A_G_IRQ_DUPLEX_CHANGE |
+ IP101A_G_IRQ_LINK_CHANGE);
+}
+
static int ip101a_g_ack_interrupt(struct phy_device *phydev)
{
int err = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS);
@@ -243,6 +258,7 @@ static struct phy_driver icplus_driver[] = {
.phy_id_mask = 0x0ffffff0,
.features = PHY_BASIC_FEATURES,
.config_intr = ip101a_g_config_intr,
+ .did_interrupt = ip101a_g_did_interrupt,
.ack_interrupt = ip101a_g_ack_interrupt,
.config_init = &ip101a_g_config_init,
.suspend = genphy_suspend,
--
2.19.1
\
 
 \ /
  Last update: 2018-11-17 19:21    [W:0.116 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site