lkml.org 
[lkml]   [2018]   [Oct]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v3] ARM: dts: imx6sx-sdb: Fix enet phy regulator
On Mon, Oct 08, 2018 at 03:28:01PM +0000, Leonard Crestez wrote:
> Bindings for "fixed-regulator" only explicitly support "gpio" property,
> not "gpios". Fix by correcting the property name.
>
> The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
> cycle, this can be handled by the phy-reset-gpios property. Sadly this
> is not handled on suspend: the fec driver turns phy-supply off but
> doesn't assert phy-reset-gpios again on resume.
>
> Since additional phy-level work is required to support powering off the
> phy in suspend fix the problem by just marking the regulator as
> "boot-on" "always-on" so that it's never turned off. This behavior is
> equivalent to older releases.
>
> Keep the phy-reset-gpios property on fec anyway because it is a correct
> description of board design.
>
> This issue was exposed by commit efdfeb079cc3 ("regulator: fixed:
> Convert to use GPIO descriptor only") which causes the "gpios" property
> to also be parsed. Before that commit the "gpios" property had no
> effect, PHY reset was only handled in the the bootloader.
>
> This fixes linux-next boot failures previously reported here:
> https://lore.kernel.org/patchwork/patch/982437/#1177900
> https://lore.kernel.org/patchwork/patch/994091/#1178304

So this is a fix we only need to apply for 4.20-rc, right?

Shawn

>
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
>
> ---
> I attempted to fix by asserting phy-reset-gpios on resume but apparently
> phy fixups are still lost and need to be reapplied (not sure why/how).
>
> Changes since v2:
> * Mark as always-on boot-enable-on because phy power cycling is hard
> * Clear Reviewed-by because of large behavior change
> * Link to v2: https://lore.kernel.org/patchwork/patch/995520/
>
> Changes since v1:
> * Use 0x10b0 for phy reset pinctrl value (Fabio)
> * Link to v1: https://lore.kernel.org/patchwork/patch/994871/
>
> arch/arm/boot/dts/imx6sx-sdb.dtsi | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi
> index 53b3408b5fab..7d7d679945d2 100644
> --- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
> +++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi
> @@ -115,11 +115,13 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet_3v3>;
> regulator-name = "enet_3v3";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> - gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
> + gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
> + regulator-boot-on;
> + regulator-always-on;
> };
>
> reg_pcie_gpio: regulator-pcie-gpio {
> compatible = "regulator-fixed";
> pinctrl-names = "default";
> @@ -178,10 +180,11 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet1>;
> phy-supply = <&reg_enet_3v3>;
> phy-mode = "rgmii";
> phy-handle = <&ethphy1>;
> + phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
> status = "okay";
>
> mdio {
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -371,10 +374,12 @@
> MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081
> MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081
> MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
> MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
> MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91
> + /* phy reset */
> + MX6SX_PAD_ENET2_CRS__GPIO2_IO_7 0x10b0
> >;
> };
>
> pinctrl_enet_3v3: enet3v3grp {
> fsl,pins = <
> --
> 2.17.1
>

\
 
 \ /
  Last update: 2018-10-09 03:10    [W:0.058 / U:2.992 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site