lkml.org 
[lkml]   [2018]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/7] clocksource: exynos_mct: Add arch_timer cooperation mode for ARM64
Date
To get ARM Architected Timers working on Samsung Exynos SoCs, one has to
first configure and enable Exynos Multi-Core Timer, because they both
share some common hardware blocks. This patch adds a mode of cooperation
with arch_timer driver, so kernel can use CP15 based timer interface via
arch_timer driver, which is mandatory on ARM64. In such mode driver only
configures MCT registers and starts the timer but don't register any
clocksource or events in the system. Those are left to be handled by
arch_timer driver.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
drivers/clocksource/exynos_mct.c | 28 ++++++++++++++++++++++------
1 file changed, 22 insertions(+), 6 deletions(-)

diff --git a/drivers/clocksource/exynos_mct.c b/drivers/clocksource/exynos_mct.c
index 43b335ff4a96..05b201ed8ef5 100644
--- a/drivers/clocksource/exynos_mct.c
+++ b/drivers/clocksource/exynos_mct.c
@@ -57,6 +57,7 @@
#define TICK_BASE_CNT 1

enum {
+ MCT_INT_NONE = 0,
MCT_INT_SPI,
MCT_INT_PPI
};
@@ -238,6 +239,9 @@ static int __init exynos4_clocksource_init(void)
{
exynos4_mct_frc_start();

+ if (!mct_int_type)
+ return 0;
+
#if defined(CONFIG_ARM)
exynos4_delay_timer.read_current_timer = &exynos4_read_current_timer;
exynos4_delay_timer.freq = clk_rate;
@@ -343,6 +347,9 @@ static struct irqaction mct_comp_event_irq = {

static int exynos4_clockevent_init(void)
{
+ if (!mct_int_type)
+ return 0;
+
mct_comp_device.cpumask = cpumask_of(0);
clockevents_config_and_register(&mct_comp_device, clk_rate,
0xf, 0xffffffff);
@@ -476,12 +483,12 @@ static int exynos4_mct_starting_cpu(unsigned int cpu)

irq_force_affinity(evt->irq, cpumask_of(cpu));
enable_irq(evt->irq);
- } else {
+ } else if (mct_int_type == MCT_INT_PPI) {
enable_percpu_irq(mct_irqs[MCT_L0_IRQ], 0);
}
- clockevents_config_and_register(evt, clk_rate / (TICK_BASE_CNT + 1),
- 0xf, 0x7fffffff);
-
+ if (mct_int_type)
+ clockevents_config_and_register(evt,
+ clk_rate / (TICK_BASE_CNT + 1), 0xf, 0x7fffffff);
return 0;
}

@@ -496,7 +503,7 @@ static int exynos4_mct_dying_cpu(unsigned int cpu)
if (evt->irq != -1)
disable_irq_nosync(evt->irq);
exynos4_mct_write(0x1, mevt->base + MCT_L_INT_CSTAT_OFFSET);
- } else {
+ } else if (mct_int_type == MCT_INT_PPI) {
disable_percpu_irq(mct_irqs[MCT_L0_IRQ]);
}
return 0;
@@ -529,7 +536,7 @@ static int __init exynos4_timer_resources(struct device_node *np, void __iomem *
&percpu_mct_tick);
WARN(err, "MCT: can't request IRQ %d (%d)\n",
mct_irqs[MCT_L0_IRQ], err);
- } else {
+ } else if (mct_int_type == MCT_INT_SPI) {
for_each_possible_cpu(cpu) {
int mct_irq = mct_irqs[MCT_L0_IRQ + cpu];
struct mct_clock_event_device *pcpu_mevt =
@@ -573,6 +580,15 @@ static int __init mct_init_dt(struct device_node *np, unsigned int int_type)

mct_int_type = int_type;

+ if (IS_ENABLED(CONFIG_ARM64) && IS_ENABLED(CONFIG_ARM_ARCH_TIMER)) {
+ struct device_node *np = of_find_compatible_node(NULL, NULL,
+ "arm,armv8-timer");
+ if (np) {
+ mct_int_type = MCT_INT_NONE;
+ of_node_put(np);
+ }
+ }
+
/* This driver uses only one global timer interrupt */
mct_irqs[MCT_G0_IRQ] = irq_of_parse_and_map(np, MCT_G0_IRQ);

--
2.17.1
\
 
 \ /
  Last update: 2018-10-08 14:52    [W:0.094 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site