lkml.org 
[lkml]   [2018]   [Oct]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] dt-bindings: spi: add stm32 qspi controller
Date
From: Ludovic Barre <ludovic.barre@st.com>

This patch adds the documentation of device tree bindings
for the STM32 QSPI controller. It is a specialized communication
interface targeting single, dual or quad SPI Flash memories (NOR/NAND).

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
.../devicetree/bindings/spi/spi-stm32-qspi.txt | 44 ++++++++++++++++++++++
1 file changed, 44 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt

diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
new file mode 100644
index 0000000..adeeb63
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
@@ -0,0 +1,44 @@
+* STMicroelectronics Quad Serial Peripheral Interface(QSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: the first contains the register location and length.
+ the second contains the memory mapping address and length
+- reg-names: should contain the reg names "qspi" "qspi_mm"
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash (NOR/NAND) must be a child of spi node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: see ./spi-bus.txt for the description
+
+Example:
+
+qspi: spi@a0001000 {
+ compatible = "st,stm32f469-qspi";
+ reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+ reg-names = "qspi", "qspi_mm";
+ interrupts = <91>;
+ resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+ clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi0>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ ...
+ };
+};
--
2.7.4
\
 
 \ /
  Last update: 2018-10-05 09:45    [W:0.065 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site