lkml.org 
[lkml]   [2018]   [Oct]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: R8169: Network lockups in 4.18.{8,9,10} (and 4.19 dev)
From
Date
Hi Heiner,

Here's the reply to your questions. Sorry for the delay.

On 28/09/2018 23:13, Heiner Kallweit wrote:
> On 29.09.2018 00:00, Chris Clayton wrote:
>> Thanks Maciej.
>>
>> On 28/09/2018 16:54, Maciej S. Szmigiero wrote:
>>> Hi,
>>>
>>>> Hi,
>>>>
>>>> I upgraded my kernel to 4.18.10 recently and have since been experiencing network problems after resuming from a
>>>> suspend to RAM or disk. I previously had 4.18.6 and that was OK.
>>>>
>>>> The pattern of the problem is that when I first boot, the network is fine. But, after resume from suspend I find that
>>>> the time taken for a ping of one of my ISP's nameservers increases from 14-15ms to more than 1000ms. Moreover, when I
>>>> open a browser (chromium or firefox), it fails to retrieve my home page (https://www.google.co.uk) and pings of the
>>>> nameserver fail with the message "Destination Host Unreachable". Often, I can revive the network by stopping it with
>>>> /sbin/if(down,up} but sometimes it is necessary to also remove the r8169 module and load it again.
>>>
>>> Please have a look at the following thread:
>>> https://lkml.org/lkml/2018/9/25/1118
>>>
>>
>> I applied your patch for the 4.18 stable kernels to 4.18.10, but the problem is not solved by it. Similarly, I applied
>> Heiner's patch to the 4.19, but again the problem is not solved.
>>
> I think we talk about two different issues here. The one the fix is for has no link to suspend/resume.
>
> Chris, the lspci output doesn't provide enough detail to determine the exact chip version.
> Can you provide the dmesg part with the XID?

$ dmesg | grep r8169
[ 5.274938] libphy: r8169: probed
[ 5.276563] r8169 0000:05:00.2 eth0: RTL8411, 80:fa:5b:08:d0:3d, XID 48800800, IRQ 29
[ 5.278158] r8169 0000:05:00.2 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 9.275275] RTL8211E Gigabit Ethernet r8169-502:00: attached PHY driver [RTL8211E Gigabit Ethernet]
(mii_bus:phy_addr=r8169-502:00, irq=IGNORE)
[ 9.460876] r8169 0000:05:00.2 eth0: No native access to PCI extended config space, falling back to CSI
[ 11.005336] r8169 0000:05:00.2 eth0: Link is Up - 100Mbps/Full - flow control rx/tx

> According to your lspci output neither MSI nor MSI-X is active.
> Do you have to use nomsi for whatever reason?
>

No, I do not use nomsi, but MSI wasn't enabled in my kernel config. I'm 99% sure that it used to be - I've no idea how
it got dropped. If I'm not sure about an option, I start by taking the recommendation in the kconfig help. Help on MSI
has a very clear "say Y". I've re-enabled it now.

Chris

> Heiner
>
>>> Maciej
>>>
>> Chris
>>
>
>

\
 
 \ /
  Last update: 2018-10-04 10:41    [W:0.108 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site