lkml.org 
[lkml]   [2018]   [Oct]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 4/9] mailbox: tegra-hsp: Add support for shared mailboxes
From
Date
Hi Thierry,

From the 0/9:
> Are you aware of any others that we need to take into account?
We would like to use upstream driver for RCE (and probably AON and SCE)
mailbox handling, too. Eventually.
> This is a bit
> of a problem because the mailbox driver doesn't really know anything
> about the direction when it starts up, so how would it make the decision
> about how to program the registers?
I'm afraid that information must be stored in the device tree.
> What's somewhat surprising is that you're saying that both FULL and
> EMPTY interrupts should be handled by the same shared interrupt. That's
> the opposite of what the recommended programming sequence is that the
> TRM specifies.
Which TRM you mean? Something here?

https://p4viewer.nvidia.com/get///hw/ar/doc/Tech_Pubs/Xavier/TRM/

I browsed through he Xavier_TRM_DP09253001v1.pdf HSP section and I could
not find any recommendations? But see below.
> Why is it better to handle both FULL and EMPTY interrupts
> with the same shared interrupt?
Only top0 has 8 interrupts, rest of the HSP blocks have only 4 (or 5 in
case of top1) interrupts per HSP available through LIC. Hogging two of
them means that only two VMs can access a HSP.
> Would it be safe to clear all of the IE registers to 0 on driver probe?
Nope, the driver should clear only the IE register for the shared
interrupt that the driver uses. Other IEs are used by other entities.
> If they are indeed separate
> for each processor, it should be fairly easy to keep track of the
> mailboxes used by the kernel and process only those.
Yes, that is what we should do. Again the directionality should be
specified in DT.
> I'm not entirely clear on what the advantages are of using the per-
> mailbox registers, or how they are supposed to be used. The existing
> documentation doesn't really explain how these are supposed to be used
> either, so I was mostly just going by trial and error.
On virtualized configs, multiple VMs can use same HSP block but each VM
must use its own interrupt. Because all the IE registers are on the same
64 KB page, the writes to the page are trapped by hypervisor, which
means that enabling or disabling an interrupt via the shared IE register
is pretty heavy operation. The per-mailbox IE registers are on a page
accessed freely by the IE, no need to trap.

If a VM uses only one empty mailbox interrupt, using a dedicated
"shared" interrupt and disabling that in GIC could be a lighter
operation, we used to do that in Parker.

--Pekka

On 10/29/2018 12:39 PM, Thierry Reding wrote:
> On Mon, Oct 29, 2018 at 12:04:22PM +0200, Pekka Pessi wrote:
>> Hi Thierry,
>>
>> There is typically one entity (aux cpu or a VM running on CCPLEX) owning the
>> "empty" or producer side of mailbox (iow, waking up on empty) and another
>> entity owning the "full" or consumer side of mailbox (waking up on full). An
>> entity should not muck with the interrupts used by the opposite side.
> Okay, that explains some of my observations. I was initially trying to
> program interrupt enables for both FULL and EMPTY interrupts for all
> mailboxes, but then I'd usually get timeouts because the consumer wasn't
> responding (i.e. the SPE wasn't getting FULL interrupts for the CCPLEX's
> TX mailbox).
>
> If I understand correctly, you're saying that the CPU should only be
> using the EMPTY interrupts for it's TX mailbox (while leaving the FULL
> interrupts completely untouched) and only the FULL interrupt for it's
> RX mailbox (while leaving the EMPTY interrupts untouched). This is a bit
> of a problem because the mailbox driver doesn't really know anything
> about the direction when it starts up, so how would it make the decision
> about how to program the registers?
>
>> One entity typically owns one shared interrupt only.  For the
>> BPMP/SCE/RCE/SPE HSP blocks the shared interrupt 0 is owned by the auxiliary
>> processor itself, the shared interrupts 1..4 are connected to LIC and are
>> available to other entities. The convention is to go through the interrupts
>> 0..4 and then using the first available shared interrupt for both full and
>> empty.
> That partially matches another of my observations. It seems like we
> can't use the shared interrupt 0 at all on at least the AON HSP. That's
> fine because that HSP instance contains the TX mailbox for TCU and by
> the current convention in the HSP driver, shared interrupt 0 would be
> aggregating the FULL interrupts, which according to the above we don't
> need for TX mailboxes.
>
> What's somewhat surprising is that you're saying that both FULL and
> EMPTY interrupts should be handled by the same shared interrupt. That's
> the opposite of what the recommended programming sequence is that the
> TRM specifies. Why is it better to handle both FULL and EMPTY interrupts
> with the same shared interrupt?
>
>> The interrupt functions should use a mask for mailboxes owned by kernel (in
>> essence what the IE register should be for the HSP shared interrupt owned by
>> the kernel) and serve only those mailboxes owned by kernel. Note that there
>> is no reset for HSP in Xavier, and the IE register contents may be stale.
> Would it be safe to clear all of the IE registers to 0 on driver probe?
> I seem to remember trying to do that and getting similar behaviour to
> what I describe above, namely that interrupts on the SPE weren't working
> anymore. I concluded that the IE register must be shared between the
> various processors, even though that's somewhat suprising given that
> there is no way to synchronize accesses to those registers, so their
> programming would be somewhat up to chance.
>
> Do you know any more about these registers? If they are indeed separate
> for each processor, it should be fairly easy to keep track of the
> mailboxes used by the kernel and process only those. Again I don't know
> how exactly to distinguish between TX and RX mailboxes because they all
> start out the same and only their use defines which direction they go.
> Currently this works because we program them as consumers by default.
> That means we enable the FULL interrupts but keep EMPTY interrupts
> disabled until a message in transmitted on the mailbox, at which point
> we enable the EMPTY interrupt. I suppose at that point we should also
> disable the FULL interrupt, given the above discussion.
>
>> And lastly, if we want to support only Xavier and later, perhaps we should
>> be more clear in the bindings? There are no mailbox-specific interrupt
>> enable registers available on Parker and your design relies on them.
> That was certainly not the intention. I thought I had seen the per-
> mailbox interrupt enable registers also in Tegra186 documentation, but
> after double-checking they're indeed not there. I don't think the driver
> currently "relies" on them because it uses them in addition to the
> HSP_IE registers. I suppose that accessing them might cause aborts on
> Tegra186 if they don't exist, though.
>
> I'm not entirely clear on what the advantages are of using the per-
> mailbox registers, or how they are supposed to be used. The existing
> documentation doesn't really explain how these are supposed to be used
> either, so I was mostly just going by trial and error.
>
> Do you know anything more on how to use these registers? I can easily
> make them Tegra194 specific in the code, but if they're aren't any clear
> advantages, it might just be easier to stick with HSP_IE programming
> only.
>
> Thierry

\
 
 \ /
  Last update: 2018-10-29 13:26    [W:0.613 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site