lkml.org 
[lkml]   [2018]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 17/25] dt-bindings: panel: Add Bananapi S070WV20-CT16 ICN6211 MIPI-DSI to RGB bridge
Date
Bananapi S070WV20-CT16 ICN6211 is 800x480, 4-lane MIPI-DSI to RGB
bridge panel, which is available on same PCB with 24-bit RGB interface.

So, this patch adds DSI specific binding details on existing
dt-bindings file.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v3:
- Use existing binding doc and update dsi details
Changes for v2:
- none

.../display/panel/bananapi,s070wv20-ct16.txt | 31 +++++++++++++++++--
1 file changed, 29 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
index 35bc0c839f49..b7855dc7c66f 100644
--- a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
+++ b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
@@ -1,12 +1,39 @@
Banana Pi 7" (S070WV20-CT16) TFT LCD Panel

+S070WV20-CT16 is 7" 800x480 panel connected through a 24-bit RGB interface.
+
+Depending on the variant, the PCB attached to the panel module either
+supports DSI, or DSI + 24-bit RGB. DSI is converted to 24-bit RGB via
+an onboard ICN6211 MIPI DSI - RGB bridge chip, then fed to the panel
+itself
+
Required properties:
-- compatible: should be "bananapi,s070wv20-ct16"
+- compatible:
+ for 24-bit RGB interface, use "bananapi,s070wv20-ct16"
+ for ICN6211 MIPI-DSI to RGB bridge, use "bananapi,s070wv20-ct16-icn6211"
+
+Required properties for RGB:
- power-supply: see ./panel-common.txt

+Required properties for MIPI-DSI to RGB:
+- reg: for DSI virtual channel used by that screen
+- avdd-supply: analog regulator dc1 switch
+- dvdd-supply: 3v3 digital regulator
+- reset-gpios: a GPIO phandle for the reset pin
+
Optional properties:
-- enable-gpios: see ./simple-panel.txt
+- enable-gpios: see ./simple-panel.txt(not available in MIPI-DSI to RGB bridge)
- backlight: see ./simple-panel.txt

This binding is compatible with the simple-panel binding, which is specified
in ./simple-panel.txt.
+
+Example:
+panel@0 {
+ compatible = "bananapi,s070wv20-ct16-icn6211";
+ reg = <0>;
+ avdd-supply = <&reg_dc1sw>;
+ dvdd-supply = <&reg_dldo1>;
+ reset-gpios = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+ backlight = <&backlight_dsi>;
+};
--
2.18.0.321.gffc6fa0e3
\
 
 \ /
  Last update: 2018-10-26 16:46    [W:0.255 / U:0.196 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site