lkml.org 
[lkml]   [2018]   [Oct]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [V3, 3/4] Documentation: dt-bindings: media: Document bindings for DW MIPI CSI-2 Host
On Fri, Oct 19, 2018 at 02:52:25PM +0200, Luis Oliveira wrote:
> Add bindings for Synopsys DesignWare MIPI CSI-2 host.
>
> Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
> ---
> Changelog
> v2-V3
> - removed IPI settings
>
> .../devicetree/bindings/media/snps,dw-csi-plat.txt | 52 ++++++++++++++++++++++
> 1 file changed, 52 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>
> diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt b/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
> new file mode 100644
> index 0000000..be3da05
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
> @@ -0,0 +1,52 @@
> +Synopsys DesignWare CSI-2 Host controller
> +
> +Description
> +-----------
> +
> +This HW block is used to receive image coming from an MIPI CSI-2 compatible
> +camera.
> +
> +Required properties:
> +- compatible: shall be "snps,dw-csi-plat"

'plat' is really part of the name of the h/w block?

> +- reg : physical base address and size of the device memory mapped
> + registers;
> +- interrupts : CSI-2 Host interrupt
> +- snps,output-type : Core output to be used (IPI-> 0 or IDI->1 or BOTH->2)
> + These values choose which of the Core outputs will be used,
> + it can be Image Data Interface or Image Pixel Interface.
> +- phys : List of one PHY specifier (as defined in
> + Documentation/devicetree/bindings/phy/phy-bindings.txt).
> + This PHY is a MIPI DPHY working in RX mode.
> +- resets : Reference to a reset controller (optional)
> +
> +The per-board settings:
> + - port sub-node describing a single endpoint connected to the camera as
> + described in video-interfaces.txt[1].

Need to say 2 ports and what is each port? Why no port #0?

> +
> +Example:
> +
> + csi2_1: csi2@3000 {
> + compatible = "snps,dw-csi-plat";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = < 0x03000 0x7FF>;
> + interrupts = <2>;
> + output-type = <2>;
> + resets = <&dw_rst 1>;
> + phys = <&mipi_dphy_rx1 0>;
> + phy-names = "csi2-dphy";

Not documented. Not really needed for a single entry, so I'd just drop
it.

> +
> + /* CSI-2 per-board settings */
> + port@1 {
> + reg = <1>;
> + csi1_ep1: endpoint {
> + remote-endpoint = <&camera_1>;
> + data-lanes = <1 2>;
> + };
> + };
> + port@2 {
> + csi1_ep2: endpoint {
> + remote-endpoint = <&vif1_ep>;
> + };
> + };
> + };
> --
> 2.7.4
>

\
 
 \ /
  Last update: 2018-10-24 19:41    [W:0.175 / U:0.708 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site