lkml.org 
[lkml]   [2018]   [Oct]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 1/2] [media] imx214: device tree binding
Date
Hi Ricardo,

Thank you for the patch.

On Tuesday, 2 October 2018 16:30:57 EEST Ricardo Ribalda Delgado wrote:
> Document bindings for imx214 camera sensor
>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
> ---
> Changelog v2:
> Laurent Pinchart:
>
> -Spell checks
> -Remove frequency
> -Identation
> -Data lanes order
>
> Thanks!
>
> .../devicetree/bindings/media/i2c/imx214.txt | 52 +++++++++++++++++++
> 1 file changed, 52 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/imx214.txt
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/imx214.txt
> b/Documentation/devicetree/bindings/media/i2c/imx214.txt new file mode
> 100644
> index 000000000000..bf3cac731eca
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/imx214.txt
> @@ -0,0 +1,52 @@
> +* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor
> +
> +The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor
> with +an active array size of 4224H x 3200V. It is programmable through an
> I2C +interface. The I2C address can be configured to to 0x1a or 0x10,

s/to to/to/

> depending on +how the hardware is wired.
> +Image data is sent through MIPI CSI-2, which is configured as 4 lanes
> +at 1440 Mbps.

I suppose this is the maxium, with the actual frequency and number of lanes
being configurable ? I would state it so explicitly then.

> +Required Properties:
> +- compatible: value should be "sony,imx214" for imx214 sensor
> +- reg: I2C bus address of the device
> +- enable-gpios: GPIO descriptor for the enable pin.
> +- vdddo-supply: Chip digital IO regulator (1.8V).
> +- vdda-supply: Chip analog regulator (2.7V).
> +- vddd-supply: Chip digital core regulator (1.12V).
> +- clocks = Reference to the xclk clock.

s/ = /: /

Same below.

> +- clock-names = Clock name, e.g. "xclk".

As the name "xclk" is mandatory I wouldn't call it an example. You can just
say

- clock-names: Shall be "xclk".

> +- clock-frequency = Frequency of the xclk clock. (Currently the
> + driver only supports <24000000>).

Please don't mention drivers in DT bindings. I would drop the reference to the
24 MHz limitation.

I would actually drop the property completely :-) I don't see why you need it,
and you don't make use of it in the driver.

> +Optional Properties:
> +- flash-leds: See ../video-interfaces.txt
> +- lens-focus: See ../video-interfaces.txt
> +
> +The imx274 device node should contain one 'port' child node with
> +an 'endpoint' subnode. For further reading on port node refer to
> +Documentation/devicetree/bindings/media/video-interfaces.txt.

Please also document the properties of the endpoint node. You can just list
the ones that are required and the ones that are optional, and reference the
same document for their definition.

> +Example:
> +
> + camera_rear@1a {
> + compatible = "sony,imx214";
> + reg = <0x1a>;
> + vdddo-supply = <&pm8994_lvs1>;
> + vddd-supply = <&camera_vddd_1v12>;
> + vdda-supply = <&pm8994_l17>;
> + lens-focus = <&ad5820>;
> + enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>;
> + clocks = <&mmcc CAMSS_MCLK0_CLK>;
> + clock-names = "xclk";
> + clock-frequency = <24000000>;
> + port {
> + imx214_ep: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1 2 3 4>;
> + link-frequencies = /bits/ 64 <480000000>;
> + remote-endpoint = <&csiphy0_ep>;
> + };
> + };
> + };

--
Regards,

Laurent Pinchart



\
 
 \ /
  Last update: 2018-10-02 15:48    [W:0.131 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site