lkml.org 
[lkml]   [2018]   [Oct]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] clocksource/drivers/fttmr010: fix invalid interrupt register access
Date
TIMER_INTR_MASK register (Base Address of Timer + 0x38) is not designed
for masking interrupts on ast2500 chips, and it's not even listed in
ast2400 datasheet, so it's not safe to access TIMER_INTR_MASK on aspeed
chips.
Similarly, TIMER_INTR_STATE register (Base Address of Timer + 0x34) is
not interrupt status register on ast2400 and ast2500 chips. Although
there is no side effect to reset the register in fttmr010_common_init(),
it's just misleading to do so.

Signed-off-by: Tao Ren <taoren@fb.com>
---
drivers/clocksource/timer-fttmr010.c | 27 ++++++++++++++-------------
1 file changed, 14 insertions(+), 13 deletions(-)

diff --git a/drivers/clocksource/timer-fttmr010.c b/drivers/clocksource/timer-fttmr010.c
index c020038ebfab..daf063c9842e 100644
--- a/drivers/clocksource/timer-fttmr010.c
+++ b/drivers/clocksource/timer-fttmr010.c
@@ -171,16 +171,17 @@ static int fttmr010_timer_set_oneshot(struct clock_event_device *evt)

/* Setup counter start from 0 or ~0 */
writel(0, fttmr010->base + TIMER1_COUNT);
- if (fttmr010->count_down)
+ if (fttmr010->count_down) {
writel(~0, fttmr010->base + TIMER1_LOAD);
- else
+ } else {
writel(0, fttmr010->base + TIMER1_LOAD);

- /* Enable interrupt */
- cr = readl(fttmr010->base + TIMER_INTR_MASK);
- cr &= ~(TIMER_1_INT_OVERFLOW | TIMER_1_INT_MATCH2);
- cr |= TIMER_1_INT_MATCH1;
- writel(cr, fttmr010->base + TIMER_INTR_MASK);
+ /* Enable interrupt */
+ cr = readl(fttmr010->base + TIMER_INTR_MASK);
+ cr &= ~(TIMER_1_INT_OVERFLOW | TIMER_1_INT_MATCH2);
+ cr |= TIMER_1_INT_MATCH1;
+ writel(cr, fttmr010->base + TIMER_INTR_MASK);
+ }

return 0;
}
@@ -287,13 +288,13 @@ static int __init fttmr010_common_init(struct device_node *np, bool is_aspeed)
fttmr010->count_down = true;
} else {
fttmr010->t1_enable_val = TIMER_1_CR_ENABLE | TIMER_1_CR_INT;
- }

- /*
- * Reset the interrupt mask and status
- */
- writel(TIMER_INT_ALL_MASK, fttmr010->base + TIMER_INTR_MASK);
- writel(0, fttmr010->base + TIMER_INTR_STATE);
+ /*
+ * Reset the interrupt mask and status
+ */
+ writel(TIMER_INT_ALL_MASK, fttmr010->base + TIMER_INTR_MASK);
+ writel(0, fttmr010->base + TIMER_INTR_STATE);
+ }

/*
* Enable timer 1 count up, timer 2 count up, except on Aspeed,
--
2.17.1
\
 
 \ /
  Last update: 2018-10-02 06:15    [W:0.239 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site