lkml.org 
[lkml]   [2018]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 1/8] dt-bindings: mfd: document stpmic1
Date
From: pascal paillet <p.paillet@st.com>

stpmic1 is a pmic from STMicroelectronics. The STPMIC1 integrates 10
regulators , 3 switches, a watchdog and an input for a power on key.

Signed-off-by: pascal paillet <p.paillet@st.com>
---
changes in v4:
* remove interrupt-parent description
* pmic1@33 renamed to pmic@33
* fix indentation

.../devicetree/bindings/mfd/st,stpmic1.txt | 131 +++++++++++++++++++++
include/dt-bindings/mfd/st,stpmic1.h | 46 ++++++++
2 files changed, 177 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmic1.txt
create mode 100644 include/dt-bindings/mfd/st,stpmic1.h

diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
new file mode 100644
index 0000000..bb19cc8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
@@ -0,0 +1,131 @@
+* STMicroelectronics STPMIC1 Power Management IC
+
+Required parent device properties:
+- compatible: "st,stpmic1"
+- reg: The I2C slave address for the STPMIC1 chip.
+- interrupts: The interrupt line the device is connected to.
+- #interrupt-cells: Should be 1.
+- interrupt-controller: Describes the STPMIC1 as an interrupt
+ controller (has its own domain). Interrupt number are the following:
+ /* Interrupt Register 1 (0x50 for latch) */
+ IT_SWOUT_R=0
+ IT_SWOUT_F=1
+ IT_VBUS_OTG_R=2
+ IT_VBUS_OTG_F=3
+ IT_WAKEUP_R=4
+ IT_WAKEUP_F=5
+ IT_PONKEY_R=6
+ IT_PONKEY_F=7
+ /* Interrupt Register 2 (0x51 for latch) */
+ IT_OVP_BOOST=8
+ IT_OCP_BOOST=9
+ IT_OCP_SWOUT=10
+ IT_OCP_OTG=11
+ IT_CURLIM_BUCK4=12
+ IT_CURLIM_BUCK3=13
+ IT_CURLIM_BUCK2=14
+ IT_CURLIM_BUCK1=15
+ /* Interrupt Register 3 (0x52 for latch) */
+ IT_SHORT_SWOUT=16
+ IT_SHORT_SWOTG=17
+ IT_CURLIM_LDO6=18
+ IT_CURLIM_LDO5=19
+ IT_CURLIM_LDO4=20
+ IT_CURLIM_LDO3=21
+ IT_CURLIM_LDO2=22
+ IT_CURLIM_LDO1=23
+ /* Interrupt Register 3 (0x52 for latch) */
+ IT_SWIN_R=24
+ IT_SWIN_F=25
+ IT_RESERVED_1=26
+ IT_RESERVED_2=27
+ IT_VINLOW_R=28
+ IT_VINLOW_F=29
+ IT_TWARN_R=30
+ IT_TWARN_F=31
+
+Optional parent device properties:
+- st,main-control-register:
+ -bit 1: Power cycling will be performed on turn OFF condition
+ -bit 2: PWRCTRL is functional
+ -bit 3: PWRCTRL active high
+- st,pads-pull-register:
+ -bit 1: WAKEUP pull down is not active
+ -bit 2: PWRCTRL pull up is active
+ -bit 3: PWRCTRL pull down is active
+ -bit 4: WAKEUP detector is disabled
+- st,vin-control-register:
+ -bit 0: VINLOW monitoring is enabled
+ -bit [1...3]: VINLOW rising threshold
+ 000 VINOK_f + 50mV
+ 001 VINOK_f + 100mV
+ 010 VINOK_f + 150mV
+ 011 VINOK_f + 200mV
+ 100 VINOK_f + 250mV
+ 101 VINOK_f + 300mV
+ 110 VINOK_f + 350mV
+ 111 VINOK_f + 400mV
+ -bit [4...5]: VINLOW hyst
+ 00 100mV
+ 01 200mV
+ 10 300mV
+ 11 400mV
+ -bit 6: SW_OUT detector is disabled
+ -bit 7: SW_IN detector is enabled.
+- st,usb-control-register:
+ -bit 3: SW_OUT current limit
+ 0: 600mA
+ 1: 1.1A
+ -bit 4: VBUS_OTG discharge is enabled
+ -bit 5: SW_OUT discharge is enabled
+ -bit 6: VBUS_OTG detection is enabled
+ -bit 7: BOOST_OVP is disabled
+
+STPMIC1 consists in a varied group of sub-devices.
+Each sub-device binding is be described in own documentation file.
+
+Device Description
+------ ------------
+st,stpmic1-onkey : Power on key, see ../input/st,stpmic1-onkey.txt
+st,stpmic1-regulators : Regulators, see ../regulator/st,stpmic1-regulator.txt
+st,stpmic1-wdt : Watchdog, see ../watchdog/st,stpmic1-wdt.txt
+
+Example:
+
+pmic: pmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupt-parent = <&gpioa>;
+ interrupts = <0 2>;
+ st,main-control-register=<0x0c>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ };
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ vdd_core: buck1 {
+ regulator-name = "vdd_core";
+ regulator-boot-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-pull-down;
+ };
+ };
diff --git a/include/dt-bindings/mfd/st,stpmic1.h b/include/dt-bindings/mfd/st,stpmic1.h
new file mode 100644
index 0000000..b2d6c83
--- /dev/null
+++ b/include/dt-bindings/mfd/st,stpmic1.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
+ * Author: Philippe Peurichard <philippe.peurichard@st.com>,
+ * Pascal Paillet <p.paillet@st.com> for STMicroelectronics.
+ */
+
+#ifndef __DT_BINDINGS_STPMIC1_H__
+#define __DT_BINDINGS_STPMIC1_H__
+
+/* IRQ definitions */
+#define IT_PONKEY_F 0
+#define IT_PONKEY_R 1
+#define IT_WAKEUP_F 2
+#define IT_WAKEUP_R 3
+#define IT_VBUS_OTG_F 4
+#define IT_VBUS_OTG_R 5
+#define IT_SWOUT_F 6
+#define IT_SWOUT_R 7
+
+#define IT_CURLIM_BUCK1 8
+#define IT_CURLIM_BUCK2 9
+#define IT_CURLIM_BUCK3 10
+#define IT_CURLIM_BUCK4 11
+#define IT_OCP_OTG 12
+#define IT_OCP_SWOUT 13
+#define IT_OCP_BOOST 14
+#define IT_OVP_BOOST 15
+
+#define IT_CURLIM_LDO1 16
+#define IT_CURLIM_LDO2 17
+#define IT_CURLIM_LDO3 18
+#define IT_CURLIM_LDO4 19
+#define IT_CURLIM_LDO5 20
+#define IT_CURLIM_LDO6 21
+#define IT_SHORT_SWOTG 22
+#define IT_SHORT_SWOUT 23
+
+#define IT_TWARN_F 24
+#define IT_TWARN_R 25
+#define IT_VINLOW_F 26
+#define IT_VINLOW_R 27
+#define IT_SWIN_F 30
+#define IT_SWIN_R 31
+
+#endif /* __DT_BINDINGS_STPMIC1_H__ */
--
1.9.1
\
 
 \ /
  Last update: 2018-10-18 11:04    [W:0.278 / U:0.368 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site