lkml.org 
[lkml]   [2018]   [Oct]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 3/4] irqchip/mbigen: add support for a MBIGEN generating SPIs
From
Date
On 16/10/18 10:15, Yang Yingliang wrote:
> Now with
> 5052875 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller"),
> we can support MBIGEN to generate message based SPIs by writing GICD_SETSPIR.
>
> The first 64-pins of each MBIGEN chip is used to generate SPIs, and each
> MBIGEN chip has several MBIGEN nodes, every node has 128 pins for generating
> LPIs. The total pins are: 64(SPIs) + 128 * node_nr(LPIs). So we can translate
> the pin index in a unified way in mbigen_domain_translate().
>
> Also Add TYPE and VEC registers that used by generating SPIs, the driver can
> access them when MBIGEN is used to generate SPIs.
>
> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
> ---
> drivers/irqchip/irq-mbigen.c | 21 +++++++++++++++++++--
> 1 file changed, 19 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/irqchip/irq-mbigen.c b/drivers/irqchip/irq-mbigen.c
> index f05998f..37c1932 100644
> --- a/drivers/irqchip/irq-mbigen.c
> +++ b/drivers/irqchip/irq-mbigen.c
> @@ -48,6 +48,7 @@
> #define MBIGEN_NODE_OFFSET 0x1000
>
> /* offset of vector register in mbigen node */
> +#define REG_MBIGEN_SPI_VEC_OFFSET 0x500
> #define REG_MBIGEN_LPI_VEC_OFFSET 0x200
>
> /**
> @@ -62,6 +63,7 @@
> * This register is used to configure interrupt
> * trigger type
> */
> +#define REG_MBIGEN_SPI_TYPE_OFFSET 0x400
> #define REG_MBIGEN_LPI_TYPE_OFFSET 0x0
>
> /**
> @@ -79,6 +81,9 @@ static inline unsigned int get_mbigen_vec_reg(irq_hw_number_t hwirq)
> {
> unsigned int nid, pin;
>
> + if (hwirq < SPI_NUM_PER_MBIGEN_CHIP)
> + return (hwirq * 4 + REG_MBIGEN_SPI_VEC_OFFSET);
> +
> hwirq -= SPI_NUM_PER_MBIGEN_CHIP;
> nid = hwirq / IRQS_PER_MBIGEN_NODE + 1;
> pin = hwirq % IRQS_PER_MBIGEN_NODE;
> @@ -92,6 +97,13 @@ static inline void get_mbigen_type_reg(irq_hw_number_t hwirq,
> {
> unsigned int nid, irq_ofst, ofst;
>
> + if (hwirq < SPI_NUM_PER_MBIGEN_CHIP) {
> + *mask = 1 << (hwirq % 32);
> + ofst = hwirq / 32 * 4;
> + *addr = ofst + REG_MBIGEN_SPI_TYPE_OFFSET;
> + return;
> + }
> +
> hwirq -= SPI_NUM_PER_MBIGEN_CHIP;
> nid = hwirq / IRQS_PER_MBIGEN_NODE + 1;
> irq_ofst = hwirq % IRQS_PER_MBIGEN_NODE;
> @@ -162,6 +174,12 @@ static void mbigen_write_msg(struct msi_desc *desc, struct msi_msg *msg)
> u32 val;
>
> base += get_mbigen_vec_reg(d->hwirq);
> +
> + if (d->hwirq < SPI_NUM_PER_MBIGEN_CHIP) {
> + writel_relaxed(msg->data, base);
> + return;
> + }

How is the GICD_SETSPI_NSR base address programmed if you're ignoring
the address stored in the message?

How do you deal with level interrupts, as you don't seem to use the
level MSI framework either?

> +
> val = readl_relaxed(base);
>
> val &= ~(IRQ_EVENT_ID_MASK << IRQ_EVENT_ID_SHIFT);
> @@ -182,8 +200,7 @@ static int mbigen_domain_translate(struct irq_domain *d,
> if (fwspec->param_count != 2)
> return -EINVAL;
>
> - if ((fwspec->param[0] > MAXIMUM_IRQ_PIN_NUM) ||
> - (fwspec->param[0] < SPI_NUM_PER_MBIGEN_CHIP))
> + if (fwspec->param[0] > MAXIMUM_IRQ_PIN_NUM)
> return -EINVAL;
> else
> *hwirq = fwspec->param[0];
>

Now, the biggest question of them all: how does it work with ACPI? Last
time I checked, there was no DT support for platforms using the MBIGEN.

My gut feeling is that it would be so much better if the SPIs generated
by the MBIGEN were configured in firmware, and the devices behind it
would just describe the corresponding SPI...

Thanks,

M.
--
Jazz is not dead. It just smells funny...

\
 
 \ /
  Last update: 2018-10-17 18:31    [W:0.228 / U:0.408 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site