lkml.org 
[lkml]   [2018]   [Oct]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH 04/11] dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy
On Mon, Oct 08, 2018 at 06:49:42PM -0500, Grygorii Strashko wrote:
> The cpsw-phy-sel driver was replaced with new PHY driver phy-gmii-sel, so
> deprecate cpsw-phy-sel bindings and update CPSW binding to use phy-gmii-sel
> PHY bindings.
>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: Tony Lindgren <tony@atomide.com>
> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
> ---
> Documentation/devicetree/bindings/net/cpsw.txt | 8 +++++++-
> 1 file changed, 7 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
> index b3acebe..69d7ef8 100644
> --- a/Documentation/devicetree/bindings/net/cpsw.txt
> +++ b/Documentation/devicetree/bindings/net/cpsw.txt
> @@ -22,7 +22,8 @@ Required properties:
> - cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection
> device. See also cpsw-phy-sel.txt for it's binding.
> Note that in legacy cases cpsw-phy-sel may be
> - a child device instead of a phandle.
> + a child device instead of a phandle
> + (DEPRECATED, use phy-gmii-sel PHY phandle).

phy-gmii-sel is outside the scope of this binding. Just say use 'phys'
property instead.

>
> Optional properties:
> - ti,hwmods : Must be "cpgmac0"
> @@ -44,6 +45,7 @@ Optional properties:
> Slave Properties:
> Required properties:
> - phy-mode : See ethernet.txt file in the same directory
> +- phys : phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt)
>
> Optional properties:
> - dual_emac_res_vlan : Specifies VID to be used to segregate the ports
> @@ -85,12 +87,14 @@ Examples:
> phy-mode = "rgmii-txid";
> /* Filled in by U-Boot */
> mac-address = [ 00 00 00 00 00 00 ];
> + phys = <&phy_gmii_sel 1 0>;
> };
> cpsw_emac1: slave@1 {
> phy_id = <&davinci_mdio>, <1>;
> phy-mode = "rgmii-txid";
> /* Filled in by U-Boot */
> mac-address = [ 00 00 00 00 00 00 ];
> + phys = <&phy_gmii_sel 2 0>;
> };
> };
>
> @@ -114,11 +118,13 @@ Examples:
> phy-mode = "rgmii-txid";
> /* Filled in by U-Boot */
> mac-address = [ 00 00 00 00 00 00 ];
> + phys = <&phy_gmii_sel 1 0>;
> };
> cpsw_emac1: slave@1 {
> phy_id = <&davinci_mdio>, <1>;
> phy-mode = "rgmii-txid";
> /* Filled in by U-Boot */
> mac-address = [ 00 00 00 00 00 00 ];
> + phys = <&phy_gmii_sel 2 0>;
> };
> };
> --
> 2.10.5
>

\
 
 \ /
  Last update: 2018-10-17 17:41    [W:0.179 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site