lkml.org 
[lkml]   [2018]   [Oct]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 6/7] Input: sx8654 - add sx8650 support
On Tue, Oct 16, 2018 at 09:34:26PM +0200, Richard Leitner wrote:
>
> On 10/16/18 7:48 PM, Dmitry Torokhov wrote:
> > On Tue, Oct 16, 2018 at 11:22:48AM +0200, Richard Leitner wrote:
> > > The sx8654 and sx8650 are quite similar, therefore add support for the
> > > sx8650 within the sx8654 driver.
> > >
>
> ...
>
> > > /* bits for I2C_REG_CHANMASK */
> > > -#define CONV_X 0x80
> > > -#define CONV_Y 0x40
> > > +#define CONV_X BIT(7)
> > > +#define CONV_Y BIT(6)
> >
> > If you are using BIT() you need to include include/linux/bitops.h
> >
> > I also would prefer conversion to using BIT() as a separate patch.
>
> OK. I'll take it out of this patch.
>
> Should I convert them (and the other #defines where it makes sense) to BIT()
> at all?

Sure as it documents the intent better, I just asked it to be split out
since each patch should solve one particular problem.

>
> >
> > > /* coordinates rate: higher nibble of CTRL0 register */
> > > #define RATE_MANUAL 0x00
> > > @@ -71,14 +75,110 @@
> > > /* power delay: lower nibble of CTRL0 register */
> > > #define POWDLY_1_1MS 0x0b
> > > +/* for sx8650, as we have no pen release IRQ there: timeout in ns following the
> > > + * last PENIRQ after which we assume the pen is lifted.
> > > + */
> > > +#define SX8650_PENIRQ_TIMEOUT (80 * 1100 * 1000)
> > > +
> > > #define MAX_12BIT ((1 << 12) - 1)
> > > +#define MAX_I2C_READ_LEN 10 /* see datasheet section 5.1.5 */
> > > +
> > > +/* channel definition */
> > > +#define CH_X 0x00
> > > +#define CH_Y 0x01
> > > +
> > > +struct sx865x_data {
> > > + u8 cmd_manual;
> > > + u8 chan_mask;
> > > + u8 has_irq_penrelease;
> > > + u8 has_reg_irqmask;
> > > + irq_handler_t irqh;
> > > +};
> > > struct sx8654 {
> > > struct input_dev *input;
> > > struct i2c_client *client;
> > > struct gpio_desc *gpio_reset;
> > > + struct hrtimer timer;
> >
> > Does this have to be hrtimer? Can regular timer be used?
>
> I'll check again if it's feasible to reduce the timer delay to something
> below the "normal" jiffy. If not I'll replace the hrtimer with a timer.

That means polling faster than 200HZ in the best case. I think it is too
much.

>
> >
> > > +
> > > + const struct sx865x_data *data;
> > > };
> > > +static enum hrtimer_restart sx865x_penrelease_timer_handler(struct hrtimer *h)
> > > +{
> > > + struct sx8654 *ts = container_of(h, struct sx8654, timer);
> > > +
> > > + input_report_key(ts->input, BTN_TOUCH, 0);
> > > + input_sync(ts->input);
> > > + dev_dbg(&ts->client->dev, "penrelease by timer\n");
> > > +
> > > + return HRTIMER_NORESTART;
> > > +}
> > > +
>
> ...
>
> > > @@ -196,10 +312,30 @@ static void sx8654_close(struct input_dev *dev)
> > > }
> > > #ifdef CONFIG_OF
> > > +static const struct of_device_id sx8654_of_match[] = {
> > > + {
> > > + .compatible = "semtech,sx8650",
> > > + .data = &sx8650_data,
> > > + }, {
> > > + .compatible = "semtech,sx8654",
> > > + .data = &sx8654_data,
> > > + }, {
> > > + .compatible = "semtech,sx8655",
> > > + .data = &sx8654_data,
> > > + }, {
> > > + .compatible = "semtech,sx8656",
> > > + .data = &sx8654_data,
> > > + }, {},
> > > +};
> > > +MODULE_DEVICE_TABLE(of, sx8654_of_match);
> > > +
> > > static int sx8654_get_ofdata(struct sx8654 *ts)
> > > {
> > > struct device *dev = &ts->client->dev;
> > > struct device_node *node = dev->of_node;
> > > + const struct of_device_id *of_id = of_match_device(sx8654_of_match,
> > > + dev);
> >
> > If you use of_device_get_match_data() you do not need to move device
> > table around.
>
> Thanks for that hint. I haven't known there's something like this ;-)
>
> >
> > > + const struct sx865x_data *data = (struct sx865x_data *)of_id->data;
> > > int err;
> > > if (!node) {
>
> ...
>
> > > @@ -327,6 +466,7 @@ static int sx8654_probe(struct i2c_client *client,
> > > }
> > > static const struct i2c_device_id sx8654_id_table[] = {
> > > + { "semtech_sx8650", 0 },
> >
> > Can we add the data here as well?
>
> Does it generate any benefit if we add it? Who should be using it?

If someone decides to use driver in non-DT environment.

>
> I found in other drivers that it's used as a fallback when
> of_device_get_match_data() returns NULL... Should I also implement it that
> way?

Yes, that would be good.

Thanks.

--
Dmitry

\
 
 \ /
  Last update: 2018-10-16 22:20    [W:0.069 / U:9.840 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site