lkml.org 
[lkml]   [2018]   [Oct]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3 1/2] mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
Date
Hi Boris,

> -----Original Message-----
> From: Boris Brezillon [mailto:boris.brezillon@bootlin.com]
> Sent: Tuesday, October 16, 2018 5:48 PM
> To: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
> Cc: Tudor Ambarus <tudor.ambarus@microchip.com>; marek.vasut@gmail.com;
> dwmw2@infradead.org; computersforpeace@gmail.com; richard@nod.at;
> linux-kernel@vger.kernel.org; nicolas.ferre@microchip.com;
> cyrille.pitchen@microchip.com; linux-mtd@lists.infradead.org; linux-arm-
> kernel@lists.infradead.org; Cristian.Birsan@microchip.com
> Subject: Re: [PATCH v3 1/2] mtd: spi-nor: add support to non-uniform SFDP SPI
> NOR flash memories
>
> On Tue, 16 Oct 2018 14:04:11 +0200
> Boris Brezillon <boris.brezillon@bootlin.com> wrote:
>
> > On Tue, 16 Oct 2018 09:51:47 +0000
> > Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> wrote:
> >
> > > Hi Tudor,
> > >
> > > This patch is breaking the 1-4-4 Read protocol for the spansion flash
> "s25fl512s".
> > >
> > > Without this patch read request command for Quad mode, 4-byte enable, is
> coming as 0xEC i.e. SPINOR_OP_READ_1_4_4_4B.
> > > But after applying this patch, read request command for Quad mode is
> coming as 0x6C i.e. SPINOR_OP_READ_1_1_4_4B.
> > >
> > > This flash also supports non-uniform erase.
> > > Can you please check and provide some suggestion?
> >
> > Are you sure the regression comes from this patch? I suspect your bug
> > comes from 41fe242979e4 ("mtd: spi-nor: fsl-quadspi: fix read error
> > for flash size larger than 16MB").
>
> I guess you're testing with an fsl-qspi controller, right? Can you try with this
> patch?

I am testing nxp-flexspi controller and doing just read of small size 0x200.
Also 1-1-1 protocol i.e. spi-rx/tx-bus-width as 1 is working fine for this flash.

Without this patch read from 1-4-4 protocol is working correctly.

--
Regards
Yogesh Gaur

>
> --->8---
>
> diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
> index 1ff3430f82c8..c47fe70c9f98 100644
> --- a/drivers/mtd/spi-nor/fsl-quadspi.c
> +++ b/drivers/mtd/spi-nor/fsl-quadspi.c
> @@ -477,9 +477,6 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q) static int
> fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd) {
> switch (cmd) {
> - case SPINOR_OP_READ_1_1_4:
> - case SPINOR_OP_READ_1_1_4_4B:
> - return SEQID_READ;
> case SPINOR_OP_WREN:
> return SEQID_WREN;
> case SPINOR_OP_WRDI:
> @@ -490,8 +487,6 @@ static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
> return SEQID_SE;
> case SPINOR_OP_CHIP_ERASE:
> return SEQID_CHIP_ERASE;
> - case SPINOR_OP_PP:
> - return SEQID_PP;
> case SPINOR_OP_RDID:
> return SEQID_RDID;
> case SPINOR_OP_WRSR:
> @@ -503,7 +498,11 @@ static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
> case SPINOR_OP_BRWR:
> return SEQID_BRWR;
> default:
> - if (cmd == q->nor[0].erase_opcode)
> + if (cmd == q->nor[0].read_opcode)
> + return SEQID_READ;
> + else if (cmd == q->nor[0].program_opcode)
> + return SEQID_PP;
> + else if (cmd == q->nor[0].erase_opcode)
> return SEQID_SE;
> dev_err(q->dev, "Unsupported cmd 0x%.2x\n", cmd);
> break;

\
 
 \ /
  Last update: 2018-10-17 03:55    [W:0.068 / U:6.508 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site