lkml.org 
[lkml]   [2018]   [Oct]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRe: [PATCH v7] regulator: fixed: Convert to use GPIO descriptor only
Date
Hello,

This patch seems to break network booting on imx6sx-sdb in linux-next
because the enet phy regulator is not on. Reverting the patch fixes
boot.

Here is the regulator definition:

reg_enet_3v3: regulator-enet-3v3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet_3v3>;
regulator-name = "enet_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
};

Here are some prints with the patch enabled:

[ 0.153150] reg-fixed-voltage regulator-enet-3v3: OUT_HIGH gflags 0x7
[ 0.153171] reg_fixed_voltage_probe(179): regulator-enet-3v3 call gpiod_get_optional gflags=0x7 ena_gpio_invert
[ 0.153218] regulator-enet-3v3 GPIO handle specifies active low - ignored
[ 0.153233] of_gpio_flags_quirks(83): regulator-enet-3v3 set active low because !enable-active-high
[ 0.153258] of_get_named_gpiod_flags: parsed 'gpios' property of node '/regulator-enet-3v3[0]' - status (0)
[ 0.153310] gpio_value: 38 set 0
[ 0.153332] gpio_direction: 38 out (0)
[ 0.153364] enet_3v3: ena_gpiod=(ptrval) ena_gpio=0 init=0 valid=1
[ 0.153377] enet_3v3: request GPIO
[ 0.153393] enet_3v3: already have gpiod
[ 0.153423] enet_3v3: 3300 mV
...
[ 3.867827] enet_3v3: GPIO enable count=0 inv=1
[ 3.872432] enet_3v3: set value 0
[ 3.875779] gpio_value: 38 set 1

That "gpio_value: 30 set 1" tracepoint is wrong, the line is set high.

It seems that gpiod_set_value will check FLAG_ACTIVE_LOW and
automatically invert so maybe ena_gpio_invert should not be used if a
full gpiod is passed to regulator?

--- drivers/regulator/fixed.c
+++ drivers/regulator/fixed.c
@@ -146,7 +146,6 @@ static int reg_fixed_voltage_probe(struct
platform_device *pdev)

drvdata->desc.fixed_uV = config->microvolts;

- cfg.ena_gpio_invert = !config->enable_high;
if (config->enabled_at_boot) {
if (config->enable_high)
gflags = GPIOD_OUT_HIGH;
All these high/low inversions and flags are extremely confusing to me.

Link to original thread: https://lkml.org/lkml/2018/9/6/485

--
Regards,
Leonard
\
 
 \ /
  Last update: 2018-10-01 20:54    [W:0.502 / U:0.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site