lkml.org 
[lkml]   [2018]   [Jan]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 04/16] iio: adc: sun4i-gpadc-iio: rework: sampling start/end code readout reg
From
Date


On 28.01.2018 14:37, Icenowy Zheng wrote:
>
>
> 于 2018年1月28日 GMT+08:00 下午9:34:17, Philipp Rossak <embed3d@gmail.com> 写到:
>>
>>
>> On 28.01.2018 09:43, Jonathan Cameron wrote:
>>> On Fri, 26 Jan 2018 16:19:29 +0100
>>> Philipp Rossak <embed3d@gmail.com> wrote:
>>>
>>>> For adding newer sensor some basic rework of the code is necessary.
>>>>
>>>> This commit reworks the code and allows the sampling start/end code
>> and
>>>> the position of value readout register to be altered. Later the
>> start/end
>>>> functions will be used to configure the ths and start/stop the
>>>> sampling.
>>>>
>>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>>>> Signed-off-by: Philipp Rossak <embed3d@gmail.com>
>>> Hmm. It almost always turns out to be a bad idea to assume a
>> particular
>>> set of registers will be consistent across a hardware family. Usual
>> convention
>>> is just to prefix them with the first supported device and use them
>> across
>>> the variants where they are correct. I.e. don't use wild cards or
>> generic
>>> names as they often end up implying a wider range of applicability
>> than
>>> we want.
>>>
>>
>> The new THS sensors seems to use the same THS ip core, only configured
>> with different amount of sensors. So for H3, A83T, H5, A80 and A64 the
>> registers are all the same.
>>
>> I think the big question is, do we want to have a few very big patches.
>>
>> Or more small patches with code that is used in later patches.
>
> Allwinner H6 has changed the THS core again.
>
> Please consider this :-)
>

Yes you are right the core is different! But it is already considered it.
They dropped ACQ1, the IRQs control/status are split in separate
registers. I already have a good idea how to implement it, but I would
like to add this in the second part of this patch series (containing
support for A80, A64, and H5) or even later since the initial support
and the CCU driver is missing right now.


>>
>>> A few other comments inline. Reworking code to make it ready for
>> later
>>> patches is fine, but this also adds a lot of new code which isn't
>> used until
>>> much later in the series. Move it there...
>>
>> please see comments below.
>>
>>>> ---
>>>> drivers/iio/adc/sun4i-gpadc-iio.c | 87
>> +++++++++++++++++++++++++++++++++++----
>>>> include/linux/mfd/sun4i-gpadc.h | 19 +++++++--
>>>> 2 files changed, 94 insertions(+), 12 deletions(-)
>>>>
>>>> diff --git a/drivers/iio/adc/sun4i-gpadc-iio.c
>> b/drivers/iio/adc/sun4i-gpadc-iio.c
>>>> index 03804ff9c006..363936b37c5a 100644
>>>> --- a/drivers/iio/adc/sun4i-gpadc-iio.c
>>>> +++ b/drivers/iio/adc/sun4i-gpadc-iio.c
>>>> @@ -49,6 +49,18 @@ static unsigned int
>> sun6i_gpadc_chan_select(unsigned int chan)
>>>> return SUN6I_GPADC_CTRL1_ADC_CHAN_SELECT(chan);
>>>> }
>>>>
>>>> +struct sun4i_gpadc_iio;
>>>> +
>>>> +/*
>>>> + * Prototypes for these functions, which enable these functions to
>> be
>>>> + * referenced in gpadc_data structures.
>>>> + */
>>>> +static int sun4i_gpadc_sample_start(struct sun4i_gpadc_iio *info);
>>>> +static int sun4i_gpadc_sample_end(struct sun4i_gpadc_iio *info);
>>>> +
>>>> +static int sunxi_ths_sample_start(struct sun4i_gpadc_iio *info);
>>>
>>> Superficially this appears to be introduced but not used... Patch 9
>>> is first to use it I think? Introduce it then rather than here.
>>>
>>
>> You are right, this function is used first in Patch 9. In an very early
>>
>> version, I had this together with Patch 9. But then I had the feeling
>> that everything got too messy... Right now this is a very big patch
>> series and I wanted to have a clear structure in it and easy to review.
>>
>> If I would rework this it will end up in squashing, Patch 4, Parts of
>> Patch 7, Patch 8 and Patch 9.
>>
>>>> +static int sunxi_ths_sample_end(struct sun4i_gpadc_iio *info);
>>>> +
>>>> struct gpadc_data {
>>>> int temp_offset;
>>>> int temp_scale;
>>>> @@ -56,6 +68,13 @@ struct gpadc_data {
>>>> unsigned int tp_adc_select;
>>>> unsigned int (*adc_chan_select)(unsigned int chan);
>>>> unsigned int adc_chan_mask;
>>>> + unsigned int temp_data;
>>>> + int (*sample_start)(struct sun4i_gpadc_iio *info);
>>>> + int (*sample_end)(struct sun4i_gpadc_iio *info);
>>>> + u32 ctrl0_map;
>>>> + u32 ctrl2_map;
>>>> + u32 sensor_en_map;
>>>> + u32 filter_map;
>>>> };
>>>>
>>>> static const struct gpadc_data sun4i_gpadc_data = {
>>>> @@ -65,6 +84,9 @@ static const struct gpadc_data sun4i_gpadc_data =
>> {
>>>> .tp_adc_select = SUN4I_GPADC_CTRL1_TP_ADC_SELECT,
>>>> .adc_chan_select = &sun4i_gpadc_chan_select,
>>>> .adc_chan_mask = SUN4I_GPADC_CTRL1_ADC_CHAN_MASK,
>>>> + .temp_data = SUN4I_GPADC_TEMP_DATA,
>>>> + .sample_start = sun4i_gpadc_sample_start,
>>>> + .sample_end = sun4i_gpadc_sample_end,
>>>> };
>>>>
>>>> static const struct gpadc_data sun5i_gpadc_data = {
>>>> @@ -74,6 +96,9 @@ static const struct gpadc_data sun5i_gpadc_data =
>> {
>>>> .tp_adc_select = SUN4I_GPADC_CTRL1_TP_ADC_SELECT,
>>>> .adc_chan_select = &sun4i_gpadc_chan_select,
>>>> .adc_chan_mask = SUN4I_GPADC_CTRL1_ADC_CHAN_MASK,
>>>> + .temp_data = SUN4I_GPADC_TEMP_DATA,
>>>> + .sample_start = sun4i_gpadc_sample_start,
>>>> + .sample_end = sun4i_gpadc_sample_end,
>>>> };
>>>>
>>>> static const struct gpadc_data sun6i_gpadc_data = {
>>>> @@ -83,12 +108,18 @@ static const struct gpadc_data sun6i_gpadc_data
>> = {
>>>> .tp_adc_select = SUN6I_GPADC_CTRL1_TP_ADC_SELECT,
>>>> .adc_chan_select = &sun6i_gpadc_chan_select,
>>>> .adc_chan_mask = SUN6I_GPADC_CTRL1_ADC_CHAN_MASK,
>>>> + .temp_data = SUN4I_GPADC_TEMP_DATA,
>>>> + .sample_start = sun4i_gpadc_sample_start,
>>>> + .sample_end = sun4i_gpadc_sample_end,
>>>> };
>>>>
>>>> static const struct gpadc_data sun8i_a33_gpadc_data = {
>>>> .temp_offset = -1662,
>>>> .temp_scale = 162,
>>>> .tp_mode_en = SUN8I_A33_GPADC_CTRL1_CHOP_TEMP_EN,
>>>> + .temp_data = SUN4I_GPADC_TEMP_DATA,
>>>> + .sample_start = sun4i_gpadc_sample_start,
>>>> + .sample_end = sun4i_gpadc_sample_end,
>>>> };
>>>>
>>>> struct sun4i_gpadc_iio {
>>>> @@ -277,7 +308,7 @@ static int sun4i_gpadc_temp_read(struct iio_dev
>> *indio_dev, int *val)
>>>> if (info->no_irq) {
>>>> pm_runtime_get_sync(indio_dev->dev.parent);
>>>>
>>>> - regmap_read(info->regmap, SUN4I_GPADC_TEMP_DATA, val);
>>>> + regmap_read(info->regmap, info->data->temp_data, val);
>>>>
>>>> pm_runtime_mark_last_busy(indio_dev->dev.parent);
>>>> pm_runtime_put_autosuspend(indio_dev->dev.parent);
>>>> @@ -382,10 +413,8 @@ static irqreturn_t
>> sun4i_gpadc_fifo_data_irq_handler(int irq, void *dev_id)
>>>> return IRQ_HANDLED;
>>>> }
>>>>
>>>> -static int sun4i_gpadc_runtime_suspend(struct device *dev)
>>>> +static int sun4i_gpadc_sample_end(struct sun4i_gpadc_iio *info)
>>>> {
>>>> - struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev));
>>>> -
>>>> /* Disable the ADC on IP */
>>>> regmap_write(info->regmap, SUN4I_GPADC_CTRL1, 0);
>>>> /* Disable temperature sensor on IP */
>>>> @@ -394,19 +423,32 @@ static int sun4i_gpadc_runtime_suspend(struct
>> device *dev)
>>>> return 0;
>>>> }
>>>>
>>>> -static int sun4i_gpadc_runtime_resume(struct device *dev)
>>>> +static int sunxi_ths_sample_end(struct sun4i_gpadc_iio *info)
>>>> +{
>>>> + /* Disable temperature sensor */
>>>> + regmap_write(info->regmap, SUNXI_THS_CTRL2, 0x0);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int sun4i_gpadc_runtime_suspend(struct device *dev)
>>>> {
>>>> struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev));
>>>>
>>>> + return info->data->sample_end(info);
>>>> +}
>>>> +
>>>> +static int sun4i_gpadc_sample_start(struct sun4i_gpadc_iio *info)
>>>> +{
>>>> /* clkin = 6MHz */
>>>> regmap_write(info->regmap, SUN4I_GPADC_CTRL0,
>>>> SUN4I_GPADC_CTRL0_ADC_CLK_DIVIDER(2) |
>>>> SUN4I_GPADC_CTRL0_FS_DIV(7) |
>>>> - SUN4I_GPADC_CTRL0_T_ACQ(63));
>>>> + SUNXI_THS_ACQ0(63));
>>>> regmap_write(info->regmap, SUN4I_GPADC_CTRL1,
>> info->data->tp_mode_en);
>>>> regmap_write(info->regmap, SUN4I_GPADC_CTRL3,
>>>> - SUN4I_GPADC_CTRL3_FILTER_EN |
>>>> - SUN4I_GPADC_CTRL3_FILTER_TYPE(1));
>>>> + SUNXI_THS_FILTER_EN |
>>>> + SUNXI_THS_FILTER_TYPE(1));
>>>
>>> Why if these are temperature sensor features are we setting them in
>> the
>>> general purpose ADC start function?
>>
>> This is part of the olds sensors (before Allwinner reworked their
>> temperature sensor (only ths) ). Those "old" sensors integrate an ADC
>> and a Thermal sensor in one ip block/register space. I don't want to
>> break those sensors/adc, since I'm not able to test them!
>>
>>>> /* period = SUN4I_GPADC_TPR_TEMP_PERIOD * 256 * 16 / clkin; ~0.6s
>> */
>>>> regmap_write(info->regmap, SUN4I_GPADC_TPR,
>>>> SUN4I_GPADC_TPR_TEMP_ENABLE |
>>>> @@ -415,6 +457,35 @@ static int sun4i_gpadc_runtime_resume(struct
>> device *dev)
>>>> return 0;
>>>> }
>>>>
>>>> +static int sunxi_ths_sample_start(struct sun4i_gpadc_iio *info)
>>>> +{
>>>> + u32 value;
>>>> +
>>>> + if (info->data->ctrl0_map)
>>>> + regmap_write(info->regmap, SUNXI_THS_CTRL0,
>>>> + info->data->ctrl0_map);
>>>> +
>>>> + regmap_write(info->regmap, SUNXI_THS_CTRL2,
>>>> + info->data->ctrl2_map);
>>>> +
>>>> + regmap_write(info->regmap, SUNXI_THS_FILTER,
>>>> + info->data->filter_map);
>>>> +
>>>> + regmap_read(info->regmap, SUNXI_THS_CTRL2, &value);
>>>> +
>>>> + regmap_write(info->regmap, SUNXI_THS_CTRL2,
>>>> + info->data->sensor_en_map | value);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int sun4i_gpadc_runtime_resume(struct device *dev)
>>>> +{
>>>> + struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev));
>>>> +
>>>> + return info->data->sample_start(info);
>>>> +}
>>>> +
>>>> static int sun4i_gpadc_get_temp(void *data, int *temp)
>>>> {
>>>> struct sun4i_gpadc_iio *info = data;
>>>> diff --git a/include/linux/mfd/sun4i-gpadc.h
>> b/include/linux/mfd/sun4i-gpadc.h
>>>> index 78d31984a222..39e096c3ddac 100644
>>>> --- a/include/linux/mfd/sun4i-gpadc.h
>>>> +++ b/include/linux/mfd/sun4i-gpadc.h
>>>> @@ -17,7 +17,6 @@
>>>> #define SUN4I_GPADC_CTRL0_ADC_CLK_SELECT BIT(22)
>>>> #define SUN4I_GPADC_CTRL0_ADC_CLK_DIVIDER(x) ((GENMASK(1, 0) &
>> (x)) << 20)
>>>> #define SUN4I_GPADC_CTRL0_FS_DIV(x) ((GENMASK(3, 0) & (x)) <<
>> 16)
>>>> -#define SUN4I_GPADC_CTRL0_T_ACQ(x) (GENMASK(15, 0) & (x))
>>>>
>>>> #define SUN4I_GPADC_CTRL1 0x04
>>>>
>>>> @@ -51,9 +50,6 @@
>>>>
>>>> #define SUN4I_GPADC_CTRL3 0x0c
>>>>
>>>> -#define SUN4I_GPADC_CTRL3_FILTER_EN BIT(2)
>>>> -#define SUN4I_GPADC_CTRL3_FILTER_TYPE(x) (GENMASK(1, 0) & (x))
>>>> -
>>>> #define SUN4I_GPADC_TPR 0x18
>>>>
>>>> #define SUN4I_GPADC_TPR_TEMP_ENABLE BIT(16)
>>>> @@ -90,6 +86,21 @@
>>>> /* 10s delay before suspending the IP */
>>>> #define SUN4I_GPADC_AUTOSUSPEND_DELAY 10000
>>>>
>>>> +/* SUNXI_THS COMMON REGISTERS + DEFINES */
>>>> +#define SUNXI_THS_CTRL0 0x00
>>>> +#define SUNXI_THS_CTRL2 0x40
>>>> +#define SUNXI_THS_FILTER 0x70
>>>> +
>>>> +#define SUNXI_THS_FILTER_EN BIT(2)
>>>> +#define SUNXI_THS_FILTER_TYPE(x) (GENMASK(1, 0) & (x))
>>>> +#define SUNXI_THS_ACQ0(x) (GENMASK(15, 0) & (x))
>>>> +#define SUNXI_THS_ACQ1(x) (GENMASK(31, 16) & ((x) << 16))
>>>> +
>>>> +#define SUNXI_THS_TEMP_SENSE_EN0 BIT(0)
>>>> +#define SUNXI_THS_TEMP_SENSE_EN1 BIT(1)
>>>> +#define SUNXI_THS_TEMP_SENSE_EN2 BIT(2)
>>>> +#define SUNXI_THS_TEMP_SENSE_EN3 BIT(3)
>>>> +
>>>> struct sun4i_gpadc_dev {
>>>> struct device *dev;
>>>> struct regmap *regmap;
>>>
>>
>> In general I'm ok with changing those things, but I would like to wait
>> for some more feedback/thoughts about this.
>>
>> Thanks,
>> Philipp
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

\
 
 \ /
  Last update: 2018-01-28 15:33    [W:0.242 / U:1.796 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site