lkml.org 
[lkml]   [2018]   [Jan]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] sh: clk: Relax clk rate match test
Hi Jacopo,

On Thu, Jan 25, 2018 at 3:14 PM, jacopo mondi <jacopo@jmondi.org> wrote:
> On Thu, Jan 25, 2018 at 02:53:41PM +0100, Geert Uytterhoeven wrote:
>> CC linux-clk (yes I know this is about the legacy SH clock framework, but
>> the public API is/should be the same)
>>
>> On Thu, Jan 25, 2018 at 12:24 PM, Jacopo Mondi
>> <jacopo+renesas@jmondi.org> wrote:
>> > When asking for a clk rate to be set, the sh core clock matches only
>> > exact rate values against the calculated frequency table entries. If the
>> > rate does not match exactly the test fails, and the whole frequency
>> > table is walked, resulting in selection of the last entry, corresponding to
>> > the lowest available clock rate.
>>
>> IIUIC, the code does not select the last entry, but returns an error code,
>> which is propagated all the way up?
>>
>> > Ie. when asking for a 10MHz clock rate on div6 clocks (ie. "video_clk" line),
>> > the calculated clock frequency 10088572 Hz gets ignored, and the clock is
>> > actually set to 5201920 Hz, which is the last available entry of the frequencies
>> > table.
>>
>> Perhaps 5201920 is just the default (or old value)?
>>
>> > Relax the clock frequency match test, allowing selection of clock rates
>> > immediately slower than the required one.
>> >
>> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
>> >
>> > ---
>> > Hello renesas lists,
>> >
>> > I'm now working on handling frame rate for the ov7720 image sensor to have that
>> > driver accepted as part of v4l2. The sensor is installed on on Migo-R board.
>> > In order to properly calculate pixel clock and the framerate I noticed the
>> > clock signal fed to the sensor from the SH7722 chip was always the lowest
>> > available one.
>> >
>> > This patch fixes the issues and allows me to properly select which clock
>> > frequency supply to the sensor, which according to datasheet does not support
>> > input clock frequencies slower than 10MHz (but works anyhow).
>> >
>> > As all patches for SH architecture I wonder where they should be picked up from,
>> > as SH seems not maintained at the moment.
>> >
>> > Thanks
>> > j
>> >
>> > ---
>> > drivers/sh/clk/core.c | 9 ++++++---
>> > 1 file changed, 6 insertions(+), 3 deletions(-)
>> >
>> > diff --git a/drivers/sh/clk/core.c b/drivers/sh/clk/core.c
>> > index 92863e3..d2cb94c 100644
>> > --- a/drivers/sh/clk/core.c
>> > +++ b/drivers/sh/clk/core.c
>> > @@ -198,9 +198,12 @@ int clk_rate_table_find(struct clk *clk,
>> > {
>> > struct cpufreq_frequency_table *pos;
>> >
>> > - cpufreq_for_each_valid_entry(pos, freq_table)
>> > - if (pos->frequency == rate)
>> > - return pos - freq_table;
>> > + cpufreq_for_each_valid_entry(pos, freq_table) {
>> > + if (pos->frequency > rate)
>> > + continue;
>>
>> This assumes all frequency tables are sorted.
>>
>> Shouldn't you pick the closest frequency?
>>
>> However, that's what clk_rate_table_round() does, which is called from
>> sh_clk_div_round_rate(), and thus already used as .round_rate:
>>
>> static struct sh_clk_ops sh_clk_div_enable_clk_ops = {
>> .recalc = sh_clk_div_recalc,
>> .set_rate = sh_clk_div_set_rate,
>> .round_rate = sh_clk_div_round_rate,
>> .enable = sh_clk_div_enable,
>> .disable = sh_clk_div_disable,
>> };
>
> Does this implies clock rates should be set using clk_round_rate() and
> not clk_set_rate() if I understand this right?

Not necessarily...

Note that both cpg_div6_clock_round_rate() and cpg_div6_clock_set_rate()
in the CCF implementation for DIV6 clocks use rounding.

>> (clk_rate_table_find() is called from sh_clk_div_set_rate())
>>
>> Or are you supposed to ask for the exact clock rate? Where does the 10 MHz
>> come from?
>
> From board initialization code, in order to provide a valid input
> clock to OV7720 sensor.

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2018-01-25 15:40    [W:0.107 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site