lkml.org 
[lkml]   [2018]   [Jan]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/2] Input: edt-ft5x06 - Add support for regulator
Hello Lothar,

Le Tue, 23 Jan 2018 09:04:14 +0100,
Lothar Waßmann <LW@KARO-electronics.de> a écrit :

> Hi,
>
> On Mon, 22 Jan 2018 09:42:08 -0800 Dmitry Torokhov wrote:
> > Hi Mylène,
> >
> > On Thu, Dec 28, 2017 at 8:33 AM, Mylène Josserand
> > <mylene.josserand@free-electrons.com> wrote:
> > > Add the support of regulator to use it as VCC source.
> > >
> > > Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
> > > ---
> > > .../bindings/input/touchscreen/edt-ft5x06.txt | 1 +
> > > drivers/input/touchscreen/edt-ft5x06.c | 33 ++++++++++++++++++++++
> > > 2 files changed, 34 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > index 025cf8c9324a..48e975b9c1aa 100644
> > > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > @@ -30,6 +30,7 @@ Required properties:
> > > Optional properties:
> > > - reset-gpios: GPIO specification for the RESET input
> > > - wake-gpios: GPIO specification for the WAKE input
> > > + - vcc-supply: Regulator that supplies the touchscreen
> > >
> > > - pinctrl-names: should be "default"
> > > - pinctrl-0: a phandle pointing to the pin settings for the
> > > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > > index c53a3d7239e7..5ee14a25a382 100644
> > > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > > @@ -39,6 +39,7 @@
> > > #include <linux/input/mt.h>
> > > #include <linux/input/touchscreen.h>
> > > #include <linux/of_device.h>
> > > +#include <linux/regulator/consumer.h>
> > >
> > > #define WORK_REGISTER_THRESHOLD 0x00
> > > #define WORK_REGISTER_REPORT_RATE 0x08
> > > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> > > struct touchscreen_properties prop;
> > > u16 num_x;
> > > u16 num_y;
> > > + struct regulator *vcc;
> > >
> > > struct gpio_desc *reset_gpio;
> > > struct gpio_desc *wake_gpio;
> > > @@ -993,6 +995,23 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > >
> > > tsdata->max_support_points = chip_data->max_support_points;
> > >
> > > + tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > > + if (IS_ERR(tsdata->vcc)) {
> > > + error = PTR_ERR(tsdata->vcc);
> > > + dev_err(&client->dev, "failed to request regulator: %d\n",
> > > + error);
> >
> I would check for -EPROBE_DEFER here and omit the error message in this
> case.
>
>
> Lothar Waßmann

Sure, I will add this case, thank you for the review.

Best regards,

--
Mylène Josserand, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

\
 
 \ /
  Last update: 2018-01-23 10:14    [W:0.161 / U:0.240 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site