lkml.org 
[lkml]   [2018]   [Jan]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 7/9] media: i2c: ov772x: Remove soc_camera dependencies
Date
Hi Jacopo,

Thank you for the patch.

On Thursday, 28 December 2017 16:01:19 EET Jacopo Mondi wrote:
> Remove soc_camera framework dependencies from ov772x sensor driver.
> - Handle clock and gpios
> - Register async subdevice
> - Remove soc_camera specific g/s_mbus_config operations
> - Change image format colorspace to SRGB

Could you explain the rationale for this ?

> - Remove sizes crop from get_selection as driver can't scale
> - Add kernel doc to driver interface header file
> - Adjust build system

That's a lot for a single patch. On the other hand I don't think splitting
this in 7 patches would be a good idea either. If you can find a better
granularity, go for it, otherwise keep it as-is. Same comment for the tw9910
driver.

> This commit does not remove the original soc_camera based driver as long
> as other platforms depends on soc_camera-based CEU driver.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
> drivers/media/i2c/Kconfig | 11 +++
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/ov772x.c | 169 ++++++++++++++++++++++++++++-------------
> include/media/i2c/ov772x.h | 8 ++-
> 4 files changed, 130 insertions(+), 59 deletions(-)
>
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index cb5d7ff..a61d7f4 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig

[snip]

> diff --git a/drivers/media/i2c/ov772x.c b/drivers/media/i2c/ov772x.c
> index 8063835..f7b293f 100644
> --- a/drivers/media/i2c/ov772x.c
> +++ b/drivers/media/i2c/ov772x.c
> @@ -1,6 +1,9 @@

[snip]

> @@ -25,8 +26,8 @@
> #include <linux/videodev2.h>
>
> #include <media/i2c/ov772x.h>
> -#include <media/soc_camera.h>
> -#include <media/v4l2-clk.h>
> +
> +#include <media/v4l2-device.h>
> #include <media/v4l2-ctrls.h>

I think C comes before D.

> #include <media/v4l2-subdev.h>
> #include <media/v4l2-image-sizes.h>

[snip]

> @@ -650,13 +653,63 @@ static int ov772x_s_register(struct v4l2_subdev *sd,
> }
> #endif
>
> +static int ov772x_power_on(struct ov772x_priv *priv)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&priv->subdev);
> + int ret;
> +
> + if (priv->info->xclk_rate)
> + ret = clk_set_rate(priv->clk, priv->info->xclk_rate);

The return value is then ignored.

I wonder whether the clk_set_rate() call shouldn't be kept in board code as
it's a board-specific frequency. DT platforms would use the assigned-clock-
rates property that doesn't require any explicit handling in the driver.

> + if (priv->clk) {
> + ret = clk_prepare_enable(priv->clk);
> + if (ret)
> + return ret;
> + }
> +
> + if (priv->pwdn_gpio) {
> + gpiod_set_value(priv->pwdn_gpio, 1);
> + usleep_range(500, 1000);
> + }
> +
> + /* Reset GPIOs are shared in some platforms. */

I'd make this a FIXME comment as this is really a hack.

/*
* FIXME: The reset signal is connected to a shared GPIO on some
* platforms (namely the SuperH Migo-R). Until a framework becomes
* available to handle this cleanly, request the GPIO temporarily
* only to avoid conflicts.
*/

Same for the tw9910 driver.

> + priv->rstb_gpio = gpiod_get_optional(&client->dev, "rstb",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(priv->rstb_gpio)) {
> + dev_info(&client->dev, "Unable to get GPIO \"rstb\"");
> + return PTR_ERR(priv->rstb_gpio);
> + }
> +
> + if (priv->rstb_gpio) {
> + gpiod_set_value(priv->rstb_gpio, 0);
> + usleep_range(500, 1000);
> + gpiod_set_value(priv->rstb_gpio, 1);
> + usleep_range(500, 1000);
> +
> + gpiod_put(priv->rstb_gpio);
> + }
> +
> + return 0;
> +}

[snip]

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2018-01-02 16:44    [W:0.139 / U:9.100 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site