lkml.org 
[lkml]   [2018]   [Jan]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 3/3] gpio: rcar: Use WAKEUP_PATH driver PM flag
On 2 January 2018 at 11:48, Rafael J. Wysocki <rafael@kernel.org> wrote:
> On Tue, Jan 2, 2018 at 11:44 AM, Geert Uytterhoeven
> <geert@linux-m68k.org> wrote:
>> Hi Rafael,
>>
>> On Tue, Jan 2, 2018 at 11:32 AM, Rafael J. Wysocki <rafael@kernel.org> wrote:
>>> On Fri, Dec 29, 2017 at 2:31 PM, Ulf Hansson <ulf.hansson@linaro.org> wrote:
>>>> From: Geert Uytterhoeven <geert+renesas@glider.be>
>>>>
>>>> Since commit ab82fa7da4dce5c7 ("gpio: rcar: Prevent module clock disable
>>>> when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO block's
>>>> module clock (if exists) is manually kept running during system suspend, to
>>>> make sure the device stays active.
>>>>
>>>> However, this explicit clock handling is merely a workaround for a failure
>>>> to properly communicate wakeup information to the PM core. Instead, set the
>>>> WAKEUP_PATH driver PM flag to indicate that the device is part of the
>>>> wakeup path, which further also enables middle-layers and PM domains (like
>>>> genpd) to act on this.
>>>>
>>>> In case the device is attached to genpd and depending on if it has an
>>>> active wakeup configuration, genpd will keep the device active (the clock
>>>> running) during system suspend when needed. This enables us to remove all
>>>> explicit clock handling code from the driver, so let's do that as well.
>>>>
>>>> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
>>>> [Ulf: Converted to use the WAKEUP_PATH driver PM flag]
>>
>> Ulf: + killing the DEV_PM_OPS define, increasing kernel size if PM_SUSPEND=n?
>>
>>>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
>>
>>>> --- a/drivers/gpio/gpio-rcar.c
>>>> +++ b/drivers/gpio/gpio-rcar.c
>>
>>>> @@ -415,6 +402,18 @@ static int gpio_rcar_parse_dt(struct gpio_rcar_priv *p, unsigned int *npins)
>>>> return 0;
>>>> }
>>>>
>>>> +#ifdef CONFIG_PM_SLEEP
>>>> +static int gpio_rcar_suspend(struct device *dev)
>>>> +{
>>>> + struct gpio_rcar_priv *p = dev_get_drvdata(dev);
>>>> +
>>>> + dev_pm_set_driver_flags(dev, p->wakeup_path ? DPM_FLAG_WAKEUP_PATH : 0);
>>>
>>> Why don't you simply set dev->power.wakeup_path here?
>>
>> That's what my v1 did (https://patchwork.kernel.org/patch/10050995/).
>
> I very much prefer this one. :-)

Okay!

The reason why I suggested inventing a new driver PM flag, was because
I consider the ->dev.power.wakeup_path, being a status flag/bit, owned
by the PM core. In other words, consumers of the flag are allowed to
look at it, but not change it.

Anyway, I am perfectly fine to drop the DPM_FLAG_WAKEUP_PATH thingy.
However, perhaps we should still add a helper function
(device_set_wakeup_path() or similar), which users can call to set the
flag?

>
> What's wrong with it?

It works, although I would rather change the assignment of the flag to
respect if the current value is true, something like this:

dev->power.wakeup_path = dev->power.wakeup_path || p->wakeup_path;

Kind regards
Uffe

\
 
 \ /
  Last update: 2018-01-02 13:54    [W:0.057 / U:3.532 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site