lkml.org 
[lkml]   [2017]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/1] usb:xhci: update condition to select bus->sysdev from parent device
From
Date
On 06.09.2017 06:47, Thang Q. Nguyen wrote:
>
>
> On Tue, Sep 5, 2017 at 6:14 PM, Mathias Nyman <mathias.nyman@linux.intel.com <mailto:mathias.nyman@linux.intel.com>> wrote:
>
> On 24.08.2017 05 <tel:24.08.2017%2005>:53, Thang Q. Nguyen wrote:
>
> On Sat, Aug 19, 2017 at 10:43 AM, Thang Q. Nguyen <tqnguyen@apm.com <mailto:tqnguyen@apm.com>> wrote:
>
> From: "Thang Q. Nguyen" <tqnguyen@apm.com <mailto:tqnguyen@apm.com>>
>
> For commit 4c39d4b949d3 ("usb: xhci: use bus->sysdev for DMA
> configuration"), sysdev points to devices known to the system firmware
> or hardware for DMA parameters.
> However, the parent of the system firmware/hardware device checking
> logic does not work in ACPI boot mode. This patch updates the formulation
> to check this case in both DT and ACPI.
>
> Signed-off-by: Tung Nguyen <tunguyen@apm.com <mailto:tunguyen@apm.com>>
> Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com <mailto:tqnguyen@apm.com>>
> ---
> Change since v1:
> - Update codes to work with kernel 4.13-rc5
> ---
> drivers/usb/host/xhci-plat.c | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
> index c04144b..1bb9729 100644
> --- a/drivers/usb/host/xhci-plat.c
> +++ b/drivers/usb/host/xhci-plat.c
> @@ -187,7 +187,10 @@ static int xhci_plat_probe(struct platform_device *pdev)
> * 3. xhci_plat is grandchild of a pci device (dwc3-pci)
> */
> sysdev = &pdev->dev;
> - if (sysdev->parent && !sysdev->of_node && sysdev->parent->of_node)
> + if (sysdev->parent && !is_of_node(sysdev->fwnode) &&
> + !is_acpi_device_node(sysdev->fwnode) &&
> + (is_of_node(sysdev->parent->fwnode) ||
> + is_acpi_device_node(sysdev->parent->fwnode)))
> sysdev = sysdev->parent;
> #ifdef CONFIG_PCI
> else if (sysdev->parent && sysdev->parent->parent &&
> --
> 1.8.3.1
>
> Is there any comment about the patch?
> With current kernel (4.13.0-rc6), booting the Linux using ACPI boot,
> kernel is crashed right after probing the USB DWC3 driver with the
> following messages:
>
>
> That should work, but the if statements are getting quite elaborate.
> How about replacing it all with:
>
> - sysdev = &pdev->dev;
> - if (sysdev->parent && !sysdev->of_node && sysdev->parent->of_node)
> - sysdev = sysdev->parent;
> -#ifdef CONFIG_PCI
> - else if (sysdev->parent && sysdev->parent->parent &&
> - sysdev->parent->parent->bus == &pci_bus_type)
> - sysdev = sysdev->parent->parent;
> -#endif
> +
> + for (sysdev = &pdev->dev; sysdev; sysdev = sysdev->parent) {
> + if (is_of_node(sysdev->fwnode) ||
> + is_acpi_device_node(sysdev->fwnode))
> + break;
> + #ifdef CONFIG_PCI
> + else if (sysdev->bus == &pci_bus_type)
> + break;
> + #endif
> + }
> +
> + if (!sysdev)
> + sysdev = &pdev->dev
>
> Does that work for you?
>
> -Mathias
>
> It works for me. I tested the followings:
> - ACPI boot: 808622B7 (DWC3) and PNP0D10 (xhci-platform)
> - DT boot: snps,dwc3 (DWC3) and xhci-platform.
> Will you apply your codes into 4.14 kernel?

I will, thanks for testing

-Mathias

\
 
 \ /
  Last update: 2017-09-06 08:29    [W:0.065 / U:1.640 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site