lkml.org 
[lkml]   [2017]   [Sep]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 2/3] thermal: hisilicon: add thermal sensor driver for Hi3660
From
Date


在 2017/9/1 5:17, Daniel Lezcano 写道:
>
> Hi Kevin,
>
>
> On 29/08/2017 10:17, Tao Wang wrote:
>> From: Tao Wang <kevin.wangtao@linaro.org>
>>
>> This patch adds the support for thermal sensor of Hi3660 SoC.
>
> for the Hi3660 SoC thermal sensor.
>
>> this will register sensors for thermal framework and use device
>> tree to bind cooling device.
>
> Is it possible to give a pointer to some documentation or to describe
> the hardware?
Yes, there used to be on patch V3, I removed it on V4.
>
> An explanation of the adc min max coef[] range[] conversion would be nice.
OK
>
> In addition, having the rational behind the average and the max would be
> nice. Do we really need both avg and max as virtual sensor?
We only need max currently.
>
>> Signed-off-by: Tao Wang <kevin.wangtao@linaro.org>
>> Signed-off-by: Leo Yan <leo.yan@linaro.org>
>> ---
>> drivers/thermal/Kconfig | 13 +++
>> drivers/thermal/Makefile | 1 +
>> drivers/thermal/hisi_tsensor.c | 209 +++++++++++++++++++++++++++++++++++++++++
>
>
> IMO, we don't need a new file, but merge this code with the current
> hisi_thermal.c driver. BTW, the hi6220 has also a tsensor which is
> different from this one.
>
> I suggest to base the hi3660 thermal driver on top of the cleanup I sent
> for the hi6220.
The tsensor of hi3660 is a different one, merging the code with hi6220 will need a lot of change.
>
>> 3 files changed, 223 insertions(+)
>> create mode 100644 drivers/thermal/hisi_tsensor.c
>>
>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>> index b5b5fac..32f582d 100644
>> --- a/drivers/thermal/Kconfig
>> +++ b/drivers/thermal/Kconfig
>> @@ -203,6 +203,19 @@ config HISI_THERMAL
>> thermal framework. cpufreq is used as the cooling device to throttle
>> CPUs when the passive trip is crossed.
>>
>> +config HISI_TSENSOR
>> + tristate "Hisilicon tsensor driver"
>> + depends on ARCH_HISI || COMPILE_TEST
>> + depends on HAS_IOMEM
>> + depends on OF
>> + default y
>> + help
>> + Enable this to plug Hisilicon's tsensor driver into the Linux thermal
>> + framework. Besides all the hardware sensors, this also support two
>> + virtual sensors, one for maximum of all the hardware sensor, and
>> + one for average of all the hardware sensor.
>> + Compitable with Hi3660 or higher.
>
> s/Compitable/Compatible/
OK
>
>> +
>> config IMX_THERMAL
>> tristate "Temperature sensor driver for Freescale i.MX SoCs"
>> depends on (ARCH_MXC && CPU_THERMAL) || COMPILE_TEST
>> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
>> index 094d703..8a16bd4 100644
>> --- a/drivers/thermal/Makefile
>> +++ b/drivers/thermal/Makefile
>> @@ -56,6 +56,7 @@ obj-$(CONFIG_ST_THERMAL) += st/
>> obj-$(CONFIG_QCOM_TSENS) += qcom/
>> obj-$(CONFIG_TEGRA_SOCTHERM) += tegra/
>> obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
>> +obj-$(CONFIG_HISI_TSENSOR) += hisi_tsensor.o
>> obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
>> obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
>> obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o
>> diff --git a/drivers/thermal/hisi_tsensor.c b/drivers/thermal/hisi_tsensor.c
>> new file mode 100644
>> index 0000000..34cf2ba
>> --- /dev/null
>> +++ b/drivers/thermal/hisi_tsensor.c
>> @@ -0,0 +1,209 @@
>> +/*
>> + * linux/drivers/thermal/hisi_tsensor.c
>> + *
>> + * Copyright (c) 2017 Hisilicon Limited.
>> + * Copyright (c) 2017 Linaro Limited.
>> + *
>> + * Author: Tao Wang <kevin.wangtao@linaro.org>
>> + * Author: Leo Yan <leo.yan@linaro.org>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; version 2 of the License.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/device.h>
>> +#include <linux/err.h>
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/of.h>
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/thermal.h>
>> +
>> +#include "thermal_core.h"
>> +
>> +#define VIRTUAL_SENSORS 2
>> +
>> +/* hisi Thermal Sensor Dev Structure */
>> +struct hisi_thermal_sensor {
>> + struct hisi_thermal_data *thermal;
>> + struct thermal_zone_device *tzd;
>> + void __iomem *sensor_reg;
>> + unsigned int id;
>> +};
>> +
>> +struct hisi_thermal_data {
>> + struct platform_device *pdev;
>> + struct hisi_thermal_sensor *sensors;
>> + unsigned int range[2];
>> + unsigned int coef[2];
>> + unsigned int max_hw_sensor;
>> +};
>> +
>> +static int hisi_thermal_get_temp(void *_sensor, int *temp)
>> +{
>> + struct hisi_thermal_sensor *sensor = _sensor;
>> + struct hisi_thermal_data *data = sensor->thermal;
>> + unsigned int idx, adc_min, adc_max, max_sensor;
>> + int val, average = 0, max = 0;
>> +
>> + adc_min = data->range[0];
>> + adc_max = data->range[1];
>> + max_sensor = data->max_hw_sensor;
>> +
>> + if (sensor->id < max_sensor) {
>> + val = readl(sensor->sensor_reg);
>> + val = clamp_val(val, adc_min, adc_max);
>
> That looks a bit fuzzy. Why not create a get_temp for physical sensor
> and another one for the virtual? So there will be a clear distinction
> between both.
make sense
>
>> + } else {
>> + for (idx = 0; idx < max_sensor; idx++) {
>> + val = readl(data->sensors[idx].sensor_reg);
>
> Below, it is assumed thermal_zone_of_sensor_register() can fail and
> sensor->tzd becomes NULL. But no check is done here with the sensor's
> tzd. Shall the code assume we take all the sensors even if a thermal
> zone failed to register ?
Yes, thermal zone failed to register didn't impact the code here. If the tzone only bind to the max SoC temperature, all the physical sensor will failed to register tzone.
>
>> + val = clamp_val(val, adc_min, adc_max);
>> + average += val;
>> + if (val > max)
>> + max = val;
>> + }
>> +
>> + if (sensor->id == max_sensor)
>> + val = max;
>> + else
>> + val = average / max_sensor;
>> + }
>>
>> + *temp = ((val - adc_min) * data->coef[0]) / (adc_max - adc_min)
>> + + data->coef[1];
>
> Pre-compute (adc_max - adc_min) at init time and check it is greater
> than zero, otherwise for a bad DT configuration we can end up with
> division by zero and crash the kernel (assuming having adc ranges in the
> DT is what we want).
OK
>
>> + return 0;
>> +}
>> +
>> +static struct thermal_zone_of_device_ops hisi_of_thermal_ops = {
>> + .get_temp = hisi_thermal_get_temp,
>> +};
>> +
>> +static void hisi_thermal_toggle_sensor(struct hisi_thermal_sensor *sensor,
>> + bool on)
>> +{
>> + struct thermal_zone_device *tzd = sensor->tzd;
>> +
>> + tzd->ops->set_mode(tzd,
>> + on ? THERMAL_DEVICE_ENABLED : THERMAL_DEVICE_DISABLED);
>> +}
>> +
>> +static int hisi_thermal_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node;
>> + struct hisi_thermal_data *data;
>> + struct hisi_thermal_sensor *sensor;
>> + struct resource *res;
>> + unsigned int max_sensor;
>> + int ret, i;
>> +
>> + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
>> + if (!data)
>> + return -ENOMEM;
>> +
>> + data->pdev = pdev;
>> + ret = of_property_read_u32(np, "hisi,tsensors", &max_sensor);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to get max sensor\n");
>> + return -EINVAL;
>> + }
>> + data->max_hw_sensor = max_sensor;
>
> Do we really need a max sensor definition in the DT? Isn't it something
> we can deduce by looping with platform_get_resource below ?
>
> eg.
>
> while ((res = platform_get_resource(..., num_sensor++)) {
> ...
> }
>
> That said, I think we can assume there are 3 sensors always, no?
If we have three CPU cluster or two cluster share the same sensor in future, that number is certain on hi3660
>
>> + data->sensors = devm_kzalloc(dev,
>> + sizeof(*data->sensors) * (max_sensor + VIRTUAL_SENSORS),
>> + GFP_KERNEL);
>> + if (IS_ERR(data->sensors)) {
>
> s/IS_ERR(data->sensors)/!data->sensors/
>
>> + dev_err(dev, "failed to alloc sensors\n");
>
> No message on memory allocation failure, there is already one from the
> mm framework.
OK
>
>> + return -ENOMEM;
>> + }
>> +
>> + ret = of_property_read_u32_array(np, "hisi,coef", data->coef, 2);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to get coef\n");
>> + return -EINVAL;
>
> return ret;
>
>> + }
>> +
>> + ret = of_property_read_u32_array(np, "hisi,adc-range", data->range, 2);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to get range\n");
>> + return -EINVAL;
>
> return ret;
OK
>
>> + }
>
> Are these data really needed through DT? Isn't it something we can hardcode?
>
>> + platform_set_drvdata(pdev, data);
>> +
>> + for (i = 0; i < max_sensor + VIRTUAL_SENSORS; ++i) {
>> + sensor = &data->sensors[i];
>> + if (i < max_sensor) {
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, i);
>
> Error check?
devm_ioremap_resource will handle it
>
>> + sensor->sensor_reg = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(sensor->sensor_reg)) {
>> + dev_err(dev, "failed to get reg base\n");
>> + return -ENOMEM;
>
> s/-ENOMEM/PTR_ERR(sensor->sensor_reg)/
OK
>
>> + }
>> + }
>> +
>> + sensor->id = i;
>
> How can we deal with holes in the DT?Do you mean the holes of sensor id?
>
>> + sensor->thermal = data;
>> + sensor->tzd = thermal_zone_of_sensor_register(dev,
>> + i, sensor, &hisi_of_thermal_ops);
>> + if (IS_ERR(sensor->tzd)) {
>> + sensor->tzd = NULL;
>> + } else {
>> + hisi_thermal_toggle_sensor(sensor, true);
>> + dev_info(dev, "thermal sensor%d registered\n", i);
>> + }
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int hisi_thermal_exit(struct platform_device *pdev)
>> +{
>> + struct hisi_thermal_data *data = platform_get_drvdata(pdev);
>> + int i;
>> +
>> + for (i = 0; i < data->max_hw_sensor + VIRTUAL_SENSORS; i++) {
>> + struct hisi_thermal_sensor *sensor = &data->sensors[i];
>> +
>> + if (!sensor->tzd)
>> + continue;
>> +
>> + hisi_thermal_toggle_sensor(sensor, false);
>> + thermal_zone_of_sensor_unregister(&pdev->dev, sensor->tzd);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id hisi_thermal_id_table[] = {
>> + { .compatible = "hisilicon,hi3660-tsensor" },
>> + {}
>> +};
>> +MODULE_DEVICE_TABLE(of, hisi_thermal_id_table);
>> +
>> +static struct platform_driver hisi_thermal_driver = {
>> + .probe = hisi_thermal_probe,
>> + .remove = hisi_thermal_exit,
>> + .driver = {
>> + .name = "hisi_tsensor",
>> + .of_match_table = hisi_thermal_id_table,
>> + },
>> +};
>> +
>> +module_platform_driver(hisi_thermal_driver);
>> +
>> +MODULE_AUTHOR("Tao Wang <kevin.wangtao@linaro.org>");
>> +MODULE_AUTHOR("Leo Yan <leo.yan@linaro.org>");
>> +MODULE_DESCRIPTION("hisi tsensor driver");
>> +MODULE_LICENSE("GPL v2");
>>
>
>

\
 
 \ /
  Last update: 2017-09-04 10:01    [W:0.207 / U:0.448 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site