lkml.org 
[lkml]   [2017]   [Sep]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 2/2] hwmon: (ltq-cputemp) add devicetree bindings documentation
Hello Rob

>>>> > +
>>>> > +Requires node properties:
>>>> > +- compatible value :
>>>> > + "lantiq,cputemp"
>>>
>>>
>>> Kind of non-specific. How is this device even accessed without any
>>> other
>>> property?
>>
>>
>> It does not need any further properties. If this is set in the device
>> tree
>> then the driver is loaded.
>
> DT is not the only way to instantiate drivers.
>
> What I meant is how do you access the hardware? That should be evident
> from the binding and it is not.

Agree with our statement.

>
> Looking at the driver, you have some memory mapped system control
> registers which get ioremapped in arch/mips/lantiq/xway/sysctrl.c and
> accesses thru some platform specific macros. That is not the ideal way
> to do things as we use syscon and regmap for such things. But that's
> all mostly kernel details not so relevant to the DT binding.

For lanitq xrx200 this is all i have. So if i have to use syscon and
regmap i am also not sure how to handle this.

> For DT, I'd expect this is a child node of the sysctrl block with a
> reg property value of <0x40 4> (along with any other child devices).
> You could also not even put this in DT and the system controller can
> have it's own driver that instantiates the child device for this
> driver.

Yes this would be the best practice. But the hardware designer for what
ever reason
placed the Register for the temperature sensors into the CGU (Clock
Generation Unit) section!
And the Register is also shared with some other stuff which is not only
assign for temperature
stuff! I am not sure how to handle this in the device tree.

This is a Register description extract from the data sheet

GPHY Configuration Register 01
This register configures the booting options of GPHY1 IP.

Offset 0x0040
Reset Value 0x01FC0000

31: RES
30: 100FX_H
29: 100FX_F
28: 10BT_F
27: 10BT_H
26: 100BT_F
25: 100BT_H
24: 1000BT_F
23: 1000BT_H
22: RES
21: RES
19: TEMP_PD <--- NEEDED Power down the Temperature Sensor
18: TEMP_HL <--- NEEDED Indicate temperature higher than 128 C
17: TEMP <--- NEEDED Value
16: TEMP <--- NEEDED Value
15: TEMP <--- NEEDED Value
14: TEMP <--- NEEDED Value
13: TEMP <--- NEEDED Value
12: TEMP <--- NEEDED Value
11: TEMP <--- NEEDED Value
10: TEMP <--- NEEDED Value
09: TEMP <--- NEEDED Value
08: RES
07: RES
06: SPI_Delay
05: SPI_Delay
04: AHB_EnD
03: DMA_OR
02: RES
01: RES
00: RES

And that is a dts tree from LEDE/Openwrt for lantiq
URL:
https://github.com/lede-project/source/blob/c88770c766fdc5599efc4672bca230017f52e8e4/target/linux/lantiq/dts/vr9.dtsi#L54

Extraction:
sram@1F000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "lantiq,sram", "simple-bus";
reg = <0x1F000000 0x800000>;
ranges = <0x0 0x1F000000 0x7FFFFF>;

eiu0: eiu@101000 {
#interrupt-cells = <1>;
interrupt-controller;
compatible = "lantiq,eiu-xway";
reg = <0x101000 0x1000>;
interrupt-parent = <&icu0>;
lantiq,eiu-irqs = <166 135 66 40 41 42>;
};

pmu0: pmu@102000 {
compatible = "lantiq,pmu-xway";
reg = <0x102000 0x1000>;
};

cgu0: cgu@103000 {
compatible = "lantiq,cgu-xway";
reg = <0x103000 0x1000>;
-> This is the place to add the binding?
};

Sorry for the noise but i am unsure how to do this.
Thanks for help

Florian

\
 
 \ /
  Last update: 2017-09-14 09:07    [W:0.132 / U:0.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site