lkml.org 
[lkml]   [2017]   [Sep]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 2/5] dt-bindings: scsi: ufs: add document for hisi-ufs
On Tue, Aug 29, 2017 at 04:41:13PM +0800, Li Wei wrote:
> add ufs node document for Hisilicon
>
> Signed-off-by: Li Wei <liwei213@huawei.com>
> ---
> Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 35 ++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt
>
> diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
> new file mode 100644
> index 000000000000..cfc84c821d50
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
> @@ -0,0 +1,35 @@
> +* Hisilicon Universal Flash Storage (UFS) Host Controller
> +
> +UFS nodes are defined to describe on-chip UFS hardware macro.
> +Each UFS Host Controller should have its own node.
> +
> +Required properties:
> +- compatible : compatible list, contains one of the following -
> + "hisilicon,hi3660-ufs" for hisi ufs host controller
> + present on Hi3660 chipset.
> +- reg : should contain UFS register address space & UFS SYS CTRL register address,
> +- interrupt-parent : interrupt device
> +- interrupts : interrupt number
> +- clocks : List of phandle and clock specifier pairs
> +- clock-names : List of clock input name strings sorted in the same
> + order as the clocks property. "clk_ref", "clk_phy" is optional
> +
> +Optional properties for board device:
> +- reset-gpio : specifies to reset devices

reset-gpios

Really, this is should be in a sub node representing the device. It's
fine if this is it, but if we start adding power supplies and other
properties it should be a separate node.

> +
> +Example:
> +
> + ufs: ufs@ff3b0000 {
> + compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs";

Need to reverse the order here. Most specific first.

> + /* 0: HCI standard */
> + /* 1: UFS SYS CTRL */
> + reg = <0x0 0xff3b0000 0x0 0x1000>,
> + <0x0 0xff3b1000 0x0 0x1000>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
> + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
> + clock-names = "clk_ref", "clk_phy";
> + freq-table-hz = <0 0>, <0 0>;
> + reset-gpio = <&gpio18 1 0>;
> + }
> --
> 2.11.0
>

\
 
 \ /
  Last update: 2017-09-01 17:54    [W:0.087 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site