lkml.org 
[lkml]   [2017]   [Aug]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V12 4/5] PCI: Handle CRS ("device not ready") returned by device after FLR
On Wed, Aug 23, 2017 at 12:56:10AM -0400, Sinan Kaya wrote:
> Sporadic reset issues have been observed with Intel 750 NVMe drive while
> assigning the physical function to the guest machine. The sequence of
> events observed is as follows:
>
> - perform a Function Level Reset (FLR)
> - sleep up to 1000ms total
> - read ~0 from PCI_COMMAND
> - warn that the device didn't return from FLR
> - touch the device before it's ready
> - device drops config writes when we restore register settings
> - incomplete register restore leaves device in inconsistent state
> - device probe fails because device is in inconsistent state
>
> After reset, an endpoint may respond to config requests with Configuration
> Request Retry Status (CRS) to indicate that it is not ready to accept new
> requests. See PCIe r3.1, sec 2.3.1 and 6.6.2.
>
> After an FLR, read the Vendor ID and use pci_bus_wait_crs() to wait for a
> value that indicates the device is ready only if CRS visibility is
> supported and device is responding with 0x0001.
>
> If pci_bus_wait_crs() fails, i.e., the device has responded with CRS status
> for at least the timeout interval, fall back to the old behavior of reading
> the Command register until it is not ~0.
>
> Also increase the timeout value from 1 second to 60 seconds to have
> consistent behavior for root ports that do and do not support CRS
> visibility.

So, after all this work, I bet you a nickel that merely increasing the
timeout from 1 sec to 60 sec (while keeping just the original PCI_COMMAND
loop) would be sufficient to fix this problem.

Reading PCI_COMMAND will cause CRS completions just like reading
PCI_VENDOR_ID will. The only difference is that there's no CRS SV
handling, and the Root Port will synthesize ~0 data when it stops retrying
the read.

If we increase the timeout, is there still value in adding the
pci_bus_wait_crs() stuff? I'm not sure there is.

> Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
> ---
> drivers/pci/pci.c | 20 ++++++++++++++++++--
> 1 file changed, 18 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> index af0cc34..5980ab3 100644
> --- a/drivers/pci/pci.c
> +++ b/drivers/pci/pci.c
> @@ -3819,19 +3819,35 @@ int pci_wait_for_pending_transaction(struct pci_dev *dev)
> */
> static void pci_flr_wait(struct pci_dev *dev)
> {
> + int timeout_ms = 60000;
> int i = 0;
> u32 id;
>
> + /*
> + * Per PCIe r3.1, sec 6.6.2, the device should finish FLR within
> + * 100ms, but even after that, it may respond to config requests
> + * with CRS status if it requires more time.
> + */
> + msleep(100);
> +
> + if (pci_bus_read_config_dword(dev->bus, dev->devfn, PCI_VENDOR_ID, &id))
> + return;
> +
> + if (pci_bus_crs_visibility_pending(id) &&
> + pci_bus_wait_crs(dev->bus, dev->devfn, id, timeout_ms))
> + return;
> +
> + timeout_ms -= 100;
> do {
> msleep(100);
> pci_read_config_dword(dev, PCI_COMMAND, &id);
> - } while (i++ < 10 && id == ~0);
> + } while (i++ < (timeout_ms / 100) && id == ~0);
>
> if (id == ~0)
> dev_warn(&dev->dev, "Failed to return from FLR\n");
> else if (i > 1)
> dev_info(&dev->dev, "Required additional %dms to return from FLR\n",
> - (i - 1) * 100);
> + i * 100);
> }
>
> /**
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

\
 
 \ /
  Last update: 2017-08-23 23:39    [W:0.065 / U:0.580 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site