lkml.org 
[lkml]   [2017]   [Aug]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v6 1/2] PCI: iproc: Retry request when CRS returned from EP
On Sun, Aug 20, 2017 at 1:56 AM, Bjorn Helgaas <helgaas@kernel.org> wrote:
> On Sun, Aug 20, 2017 at 01:02:09AM +0530, Oza Oza wrote:
>> On Sat, Aug 19, 2017 at 11:56 PM, Bjorn Helgaas <helgaas@kernel.org> wrote:
>
>> > I think you should do something like this instead so you don't do the
>> > MMIO read any more times than necessary:
>> >
>> > static u32 iproc_pcie_cfg_retry(void __iomem *cfg_data_p)
>> > {
>> > u32 data;
>> > int timeout = CFG_RETRY_STATUS_TIMEOUT_US;
>> >
>> > data = readl(cfg_data_p);
>> > while (data == CFG_RETRY_STATUS && timeout--) {
>> > udelay(1);
>> > data = readl(cfg_data_p);
>> > }
>> >
>> > if (data == CFG_RETRY_STATUS)
>> > data = 0xffffffff;
>> > return data;
>> > }
>> >
>> > static int iproc_pcie_config_read(...)
>> > {
>> > u32 data;
>> >
>> > ...
>> > data = iproc_pcie_cfg_retry(cfg_data_p);
>> > if (size <= 2)
>> > *val = (data >> (8 * (where & 3))) & ((1 << (size * 8)) - 1);
>> >
>> > In the event of a timeout, this returns PCIBIOS_SUCCESSFUL and
>> > 0xffffffff data. That's what most other platforms do, and most
>> > callers of the PCI config accessors check for that data instead of
>> > checking the return code to see whether the access was successful.
>> >
>> I see one problem with this.
>> we have Samsung NVMe which exposes 64-bit IO BAR.
>> 0xffff0001.
>>
>> and if you see __pci_read_base which does following in sequence.
>>
>> pci_read_config_dword(dev, pos, &l);
>> pci_write_config_dword(dev, pos, l | mask);
>> pci_read_config_dword(dev, pos, &sz);
>> pci_write_config_dword(dev, pos, l);
>>
>> returning 0xffffffff would not be correct in that case.
>> even if callers retry, they will end up in a loop if caller retries.
>>
>> hence I was returning 0xffff0001, it is upto the upper layer to treat
>> it as data or not.
>
> In your patch, I don't think the upper layer will ever see 0xffff0001.
> iproc_pcie_config_read() only updates *data if iproc_pcie_cfg_retry()
> returns PCIBIOS_SUCCESSFUL. And iproc_pcie_cfg_retry() only returns
> PCIBIOS_SUCCESSFUL if it reads something other than 0xffff0001.
>
> Even if you *did* return 0xffff0001 to upper layers, I think we'd have
> a problem. Here's an example scenario. If we do a Function-Level
> Reset, pcie_flr() starts the reset, then calls pci_flr_wait() to wait
> until the device becomes ready again. pci_flr_wait() thinks that any
> PCI_COMMAND value other than 0xffffffff means the device is ready.
>
> If the device returns CRS status and you return 0xffff0001 when
> pci_flr_wait() reads PCI_COMMAND, it thinks that means the device is
> ready, but it's not.
>
>> let me know if this sounds like a problem to you as well.
>>
>> so in my opinion returning 0xffffffff is not an option.
>>
>> > For example, pci_flr_wait() assumes that if a read of PCI_COMMAND
>> > returns ~0, it's because the device isn't ready yet, and we should
>> > wait and retry.

yes that will be a problem if I return 0xffff0001.
ok let me revise the patch by returning 0xffffffff as of now.

Regards,
Oza.

\
 
 \ /
  Last update: 2017-08-20 05:42    [W:2.449 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site