lkml.org 
[lkml]   [2017]   [Aug]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 3/5] arm64: dts: rockchip: add tsadc node for rk3328 SoC
Date
Am Freitag, 11. August 2017, 17:45:00 CEST schrieb rocky.hao:
>
> 在 2017/8/11 14:38, Caesar Wang 写道:
> > 在 2017年08月04日 16:06, Rocky Hao 写道:
> >> add tsadc needed main information for rk3328 SoC.
> >> 50000Hz is the max clock rate supported by tsadc module.
> >>
> >> Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
> >> ---
> >> Change in v2:
> >> - remove gerrit Change-Id
> >>
> >> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 20 ++++++++++++++++++++
> >> 1 file changed, 20 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> >> b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> >> index db4b2708084d..186fb93fdffd 100644
> >> --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> >> +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> >> @@ -308,6 +308,26 @@
> >> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> >> };
> >> + tsadc: tsadc@ff250000 {
> >> + compatible = "rockchip,rk3328-tsadc";
> >> + reg = <0x0 0xff250000 0x0 0x100>;
> >> + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH 0>;
> >> + rockchip,grf = <&grf>;
> >> + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
> >> + clock-names = "tsadc", "apb_pclk";
> >> + assigned-clocks = <&cru SCLK_TSADC>;
> >> + assigned-clock-rates = <50000>;
> >> + resets = <&cru SRST_TSADC>;
> >> + reset-names = "tsadc-apb";
> >> + pinctrl-names = "init", "default", "sleep";
> >> + pinctrl-0 = <&otp_gpio>;
> >> + pinctrl-1 = <&otp_out>;
> >> + pinctrl-2 = <&otp_gpio>;
> >> + #thermal-sensor-cells = <1>;
> >
> > Only one sensor, so maybe the value should be 0.
> Caesar, #thermal-sensor-cells means parameter counts used to match the
> proper sensor registered. Both 0 and 1 work well.
>
> Case 0, i.e. #thermal-sensor-cells = <0>, it uses the default channel
> number 0 to match tsadc channal.
> Case 1, i.e. #thermal-sensor-cells = <1>, it uses the setting
> "thermal-sensors = <&tsadc 0>;" to match tsadc channal.
>
> Case 1 provides more readable info than case 0. By my understanding,
> using the default value such as case 0, is not a good coding style.

Also, the binding for the tsadc controller specifies
#thermal-sensor-cells: 1

And the IP block in general can of course handle multiple channels,
so it should also stay that way in the dts.


Heiko

> >
> >> + rockchip,hw-tshut-temp = <100000>;
> >> + status = "disabled";
> >> + };
> >> +
> >> saradc: adc@ff280000 {
> >> compatible = "rockchip,rk3328-saradc",
> >> "rockchip,rk3399-saradc";
> >> reg = <0x0 0xff280000 0x0 0x100>;
> >
> >
> >
> >
>
>
>


\
 
 \ /
  Last update: 2017-08-11 11:48    [W:0.099 / U:0.996 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site