lkml.org 
[lkml]   [2017]   [Jul]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 3/3] power: wm831x_power: Support USB charger current limit management
Hi,

On Wed, Jul 26, 2017 at 11:05:25AM +0800, Baolin Wang wrote:
> On 25 July 2017 at 17:59, Sebastian Reichel
> <sebastian.reichel@collabora.co.uk> wrote:
> > On Tue, Jul 25, 2017 at 04:00:01PM +0800, Baolin Wang wrote:
> >> Integrate with the newly added USB charger interface to limit the current
> >> we draw from the USB input based on the input device configuration
> >> identified by the USB stack, allowing us to charge more quickly from high
> >> current inputs without drawing more current than specified from others.
> >>
> >> Signed-off-by: Mark Brown <broonie@kernel.org>
> >> Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
> >> ---
> >> Documentation/devicetree/bindings/mfd/wm831x.txt | 1 +
> >> drivers/power/supply/wm831x_power.c | 58 ++++++++++++++++++++++
> >> 2 files changed, 59 insertions(+)
> >>
> >> diff --git a/Documentation/devicetree/bindings/mfd/wm831x.txt b/Documentation/devicetree/bindings/mfd/wm831x.txt
> >> index 9f8b743..4e3bc07 100644
> >> --- a/Documentation/devicetree/bindings/mfd/wm831x.txt
> >> +++ b/Documentation/devicetree/bindings/mfd/wm831x.txt
> >> @@ -31,6 +31,7 @@ Required properties:
> >> ../interrupt-controller/interrupts.txt
> >>
> >> Optional sub-nodes:
> >> + - usb-phy : Contains a phandle to the USB PHY.
> >> - regulators : Contains sub-nodes for each of the regulators supplied by
> >> the device. The regulators are bound using their names listed below:
> >>
> >> diff --git a/drivers/power/supply/wm831x_power.c b/drivers/power/supply/wm831x_power.c
> >> index 7082301..d3948ab 100644
> >> --- a/drivers/power/supply/wm831x_power.c
> >> +++ b/drivers/power/supply/wm831x_power.c
> >> @@ -13,6 +13,7 @@
> >> #include <linux/platform_device.h>
> >> #include <linux/power_supply.h>
> >> #include <linux/slab.h>
> >> +#include <linux/usb/phy.h>
> >>
> >> #include <linux/mfd/wm831x/core.h>
> >> #include <linux/mfd/wm831x/auxadc.h>
> >> @@ -31,6 +32,8 @@ struct wm831x_power {
> >> char usb_name[20];
> >> char battery_name[20];
> >> bool have_battery;
> >> + struct usb_phy *usb_phy;
> >> + struct notifier_block usb_notify;
> >> };
> >>
> >> static int wm831x_power_check_online(struct wm831x *wm831x, int supply,
> >> @@ -125,6 +128,43 @@ static int wm831x_usb_get_prop(struct power_supply *psy,
> >> POWER_SUPPLY_PROP_VOLTAGE_NOW,
> >> };
> >>
> >> +/* In milliamps */
> >> +static const unsigned int wm831x_usb_limits[] = {
> >> + 0,
> >> + 2,
> >> + 100,
> >> + 500,
> >> + 900,
> >> + 1500,
> >> + 1800,
> >> + 550,
> >> +};
> >> +
> >> +static int wm831x_usb_limit_change(struct notifier_block *nb,
> >> + unsigned long limit, void *data)
> >> +{
> >> + struct wm831x_power *wm831x_power = container_of(nb,
> >> + struct wm831x_power,
> >> + usb_notify);
> >> + unsigned int i, best;
> >> +
> >> + /* Find the highest supported limit */
> >> + best = 0;
> >> + for (i = 0; i < ARRAY_SIZE(wm831x_usb_limits); i++) {
> >> + if (limit >= wm831x_usb_limits[i] &&
> >> + wm831x_usb_limits[best] < wm831x_usb_limits[i])
> >> + best = i;
> >> + }
> >> +
> >> + dev_dbg(wm831x_power->wm831x->dev,
> >> + "Limiting USB current to %umA", wm831x_usb_limits[best]);
> >> +
> >> + wm831x_set_bits(wm831x_power->wm831x, WM831X_POWER_STATE,
> >> + WM831X_USB_ILIM_MASK, best);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> /*********************************************************************
> >> * Battery properties
> >> *********************************************************************/
> >> @@ -607,6 +647,19 @@ static int wm831x_power_probe(struct platform_device *pdev)
> >> }
> >> }
> >>
> >> + power->usb_phy = devm_usb_get_phy_by_phandle(&pdev->dev,
> >> + "usb-phy", 0);
> >> + if (!IS_ERR(power->usb_phy)) {
> >> + power->usb_notify.notifier_call = wm831x_usb_limit_change;
> >> + ret = usb_register_notifier(power->usb_phy,
> >> + &power->usb_notify);
> >> + if (ret) {
> >> + dev_err(&pdev->dev, "Failed to register notifier: %d\n",
> >> + ret);
> >> + goto err_bat_irq;
> >> + }
> >> + }
> >
> > No error handling for power->usb_phy? I think you should bail out
> > for all errors except for "not defined in DT". Especially I would
> > expect probe defer handling in case the power supply driver is
> > loaded before the phy driver.
>
> Make sense. So I think I need to change like below:
>
> power->usb_phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0);
> if (!IS_ERR(power->usb_phy)) {
> power->usb_notify.notifier_call = wm831x_usb_limit_change;
> ret = usb_register_notifier(power->usb_phy, &power->usb_notify);
> if (ret) {
> dev_err(&pdev->dev, "Failed to register notifier: %d\n", ret);
> goto err_bat_irq;
> }
> } else if (PTR_ERR(power->usb_phy) != -ENODEV &&
> PTR_ERR(power->usb_phy) != -EINVAL) {
> ret = PTR_ERR(power->usb_phy);
> dev_err(&pdev->dev, "Failed to find USB phy: %d\n", ret);
> goto err_bat_irq;
> }
>
> The return value -EINVAL means the platform device does not have a
> device node and -ENODEV means we did not set the 'usb-phy' phandle,
> other errors we should bail out including -PROBE_DEFER. Is it OK for
> you?

Yes, but I think the following is better, which avoids
spamming the log with probe defer messages.

power->usb_phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0);
ret = PTR_ERR_OR_ZERO(power->usb_phy);

switch (ret) {
case 0:
power->usb_notify.notifier_call = wm831x_usb_limit_change;
ret = usb_register_notifier(power->usb_phy, &power->usb_notify);
if (ret) {
dev_err(&pdev->dev, "Failed to register notifier: %d\n", ret);
goto err_bat_irq;
}
break;
case -EINVAL:
case -ENODEV:
/* ignore missing usb-phy, it's optional */
power->usb_phy = NULL;
break;
default:
dev_err(&pdev->dev, "Failed to find USB phy: %d\n", ret);
/* fall-through */
case -EPROBE_DEFER:
goto err_bat_irq;
break;
}

-- Sebastian
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-07-26 14:10    [W:0.078 / U:17.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site